1) face contact
接压接触
2) contact pressure
接触压力
1.
Calculation of contact pressure on TM and VAMACE premium connection casing couplings;
TM和VAMACE特殊螺纹套管接箍接触压力计算
2.
The effect of articular step-off and neniscectomy on joint alignment and contact pressures for fractures of the lateral tibial plateau;
胫骨外侧髁骨折塌陷对关节轴线及接触压力的影响
3.
Single chip microcomputer-based inspection of catenaries-pantograph contact pressure;
基于单片机的弓网接触压力检测
3) contacting pressure
接触压力
1.
Research on contacting pressure in ball-spinning;
滚珠旋压工艺中成形区接触压力的分析计算
2.
A pin-on-disk test rig was used to investigate the influence of sliding speed and contacting pressure on the friction and wear behavior of 45CrNi pair under dry sliding condition.
利用销盘摩擦磨损试验机,考察了干滑动摩擦条件下滑动速度、接触压力对45CrNi摩擦副摩擦磨损性能的影响。
3.
The progressive cavity pump(PCP) distortions,forces and contacting instance of different pressure with the finite element analysis method are analyzed,the PCP two-dimension finite element model is constituted,the stress distributing correspond to the PCP stator rubber and the contacting pressure of the stator and rotor are obtained in this paper.
用有限元方法对螺杆泵在不同压力作用下的变形、受力及接触情况进行了分析研究,建立了螺杆泵的二维有限元模型,得出了在相应情况下螺杆泵定子橡胶的应力分布和螺杆泵定子与转子的接触压力。
4) oblique contact
斜压接触
1.
The finite element model for contact analysis between roller and tyre under oblique contact status was established,the 3D contact finite element modeling program between roller and tyre under mixed coordinate was developed.
建立了能精确反映托轮滚圈斜压接触的有限元模型,开发了一套完整的建立在混合标架下的托轮滚圈的三维接触有限元建模程序。
2.
The character of the oblique contact model between kiln roller and tyre was studied,the build-up procedure of oblique contact model between kiln roller and tyre was developed,which is apt to the finite element analysis of roller and tyre under the condition of any load,load rate,oblique angle.
研究了斜压状态下托轮滚圈多体接触模型的特点,开发了斜压接触下托轮滚圈有限元建模程序,该程序适用于任何载荷、载荷比、偏斜角下托轮滚圈的接触有限元分析。
5) touch voltage
接触电压
1.
By analyzing the effects of touch voltage and equipotential bonding on low voltage distribution system,makes clear the importance and necessity of equipotential bonding on design and construction.
通过对接触电压、等电位联结在低压配电系统中作用的分析,进一步明确等电位联结在设计、施工中的重要性及必要性。
2.
To equalize the potential and decrease touch voltage and step voltage on the earth s surface, an optimum design of grounding systems is proposed in this paper.
为了均匀地表面的电位分布 ,进一步降低接触电压和跨步电压 ,更好地保障人身和设备的安全 ,论文提出了接地系统优化设计方法。
3.
When the thickness of the low resistivity soil layer increases from the top of the grounding grid to the bottom of the grounding grid, the grounding resistance will increase dramatically and the touch voltage quickly decrease.
当受影响的地表层的厚度从小于地网埋深变化到大于地网的埋深时 ,接地电阻的减小有一个跃变 ,接触电压将急剧减小 ,低于正常情况时的对应值。
6) contact flattening
接触压扁
1.
FEM fitting of contact flattening equation of working rolls in cold strip steel rolling;
有限元法修正冷轧带钢工作辊接触压扁公式
补充资料：接触压力
分子式：
CAS号：
性质：胶接施工时，胶接件固化过程中不再另行施加其他压力，仅靠胶接件自身的质量所产生的压力。
CAS号：
性质：胶接施工时，胶接件固化过程中不再另行施加其他压力，仅靠胶接件自身的质量所产生的压力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条