说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 撑螺栓
1)  stay bolt
撑螺栓
2)  supporting bolt
支撑螺栓
1.
Analysis on failure of supporting bolt for compressor cylinder;
压缩机缸体支撑螺栓失效分析
3)  stay rod bolt
撑杆螺栓
4)  bolted through stay
螺栓拉撑杆
5)  throat-brace eye bolt
喉撑眼螺栓
6)  expansion staybolt
伸缩撑螺栓
补充资料:齿轮轮齿渐开线、螺栓、弹簧autolsp源程序
 

一、齿轮轮齿渐开渐开线


(defun c:gear(/)
(
 setq
p0 (getpoint"输入齿轮中心p0: ")
m  (getreal"输入齿轮模数M: ")
z  (getint"输入齿轮齿数Z: ")
ha 1
c 0.25
a (/ pi 9)
ra(/ (* (+ z (+ ha ha)) m) 2)
rf(/ (* (- z (+ (+ ha ha) c)) m) 2)
r(/ ( * m z) 2)
rb ( * r (cos a))
ri rb
ang 0
g (polar p0 ang rb)
)
(command "circle" p0 ra)
(command "circle" p0 rf)
(command "circle" p0 r)
(command "line"  g)
 
(while (< ri ra)
(setq
ang ( + ang(/ pi 360))
ri ( / rb (cos ang))
cta ( - (/ (sin ang) (cos ang)) ang)
g(polar p0 cta ri)
)


(command g)
)
(command )
)



二、螺旋源程序


(defun errMsg (s)
  (if (/= s "function cancelled") (princ (strcat "\nError: " s)))
     ; 当命令执行时出现错误
  (setvar "cmdecho" ocmdold)                                      ; 例如用户按下了CTRL + C
  (setvar "osmode" osmold)
  (setq *error* olderr)   ; 恢复旧的错误处理
  (princ)
)


(defun c:3Dthread (/ radouter threadpitch threadlength threadangle
                   ptStart innerdiafactor radmid radinner ocmdold osmold 4H 5H 6H h6 g6)
   ;-------------------------------------------------------------------
   ; 获取公制外径大小、螺距总长
   ; 然后计算一系列几何点
   ; 并且关闭对象捕捉、命令回显
   ;-------------------------------------------------------------------
   (setq 4H (list 0.0015 0.002 0.002 0.0025 0.003 0.0035 0.004 0.005 0.006 0.007 0.008 0.009 0.010))  
   (setq 5H (list 0.002 0.0025 0.003 0.004 0.0045 0.0055 0.0065 0.0075 0.009 0.010 0.0115 0.0125 0.0135))  
   (setq 6H (list 0.003 0.004 0.0045 0.0055 0.0065 0.008 0.0095 0.011 0.0125 0.0145 0.016 0.018 0.020))  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条