2) Conical ring
锥形环件
1.
Based on the simulation software Abaqus,the numerical simulation of rolling process of conical ring with inner steps was taken.
以Abaqus三维有限元模拟软件为平台,对内台阶锥形环件的轧制过程进行了数值模拟,通过模拟计算揭示了内台阶锥形环件轧制缺陷的形成机理。
2.
The numerical simulation of hot rolling process of LD10 aluminum alloy conical ring with inner steps was taken based on the experimental data.
采用Gleeble3500热模拟实验机进行了压缩实验,分析了LD10铝合金的高温力学性能;在D51-160热轧环机上进行热轧实验,确定了LD10铝合金环件初始轧制温度为470℃;以实验数据为基础,对LD10铝合金内台阶锥形环件的热轧过程进行了数值模拟,分析了LD10铝合金内台阶锥形环件轧制缺陷形成机制,并对预轧制环件进行了设计;通过热轧实验对数值模拟结果进行了实验验证。
3) cone
[英][kəʊn] [美][kon]
锥形铜环
4) steel taper ring
锥形钢环
5) conical trephine
锥形环钻
6) the pressure of conical ring
锥形环压力
1.
The reasons of electrode accidents are analyzed from the five sides: electrode cohesion device,the quality of electrode paste,the pressure of conical ring,the particle size of electrode paste,the height of paste column,and the measures to reduce electrode accidents are put forward.
从电极抱紧装置、电极糊质量、锥形环压力、电极糊粒度、糊柱高度等5个方面对造成电极事故的原因进行了分析,并提出了减少电极事故的措施。
补充资料:DSH型双螺旋锥形混合机
工作原理
本机双螺旋为非对称排列,一大一小扩大搅拌范围,混合速度快,混合质量均匀,因而对比重悬殊、混配比悬殊的物料混合更适合。对颗粒物料的磨损和压馈微小,对热敏性物料混合不产生过热危险。混合后的制剂稳定,不发生分层及离析现象。密封无尘,操作简单、运行安全、维修方便,使用寿命长。
应用范围
双螺旋锥形混合机是一种高效的粉体或颗粒物混合设备,它广泛适用于化工、农药、染料、医药、食品、饲料、石油、冶金、矿山等行业的各种粉体颗粒的混合。
技术参数
型号 | DSH0.3 | DSH0.5 | DSH1 | DSH2 | DSH4 | DSH6 | DSH10 |
全容积(m3) | 0.3 | 0.5 | 1 | 2 | 4 | 6 | 10 |
装载系数 | 0.4-0.6 | ||||||
混合物料(μm) | 40-300 | ||||||
工作条件 | 常温、常压、粉尘密封 | ||||||
每次产量(kg)P=1g/cm3 | 180 | 300 | 600 | 1200 | 2400 | 3600 | 6000 |
功率(kw) | 2.2 | 2.2 | 5.5 | 5.5 | 11 | 20.7 | 20.7 |
混合时间(min) | 4-6(特殊物料由实验确定) | ||||||
整机重量(kg) | 5000 | 1000 | 1200 | 1500 | 2800 | 3500 | 4500 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条