说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 非预应力的钢筋
1)  nonprestressed reinforcement
非预应力的钢筋
2)  non_prestressed steel
非预应力钢筋
1.
The laws of variation of mechanical behaviors with the temperature are investigated for prestressed steel and non_prestressed steel.
通过对21根Φ16月牙纹钢筋、45根12及8光圆钢筋、24根s5高强碳素钢丝高温下的力学性能试验,研究了预应力钢筋和非预应力钢筋的力学性能在高温下的变化规律。
3)  stress state of non-prestressed steel
非预应力钢筋应力状态
1.
A good knowledge of the stress state of non-prestressed steel in the beams is essential.
因此,清楚地认识梁中非预应力钢筋应力状态及其变化十分必要。
4)  ordinary steel reinforcement
非预应力普通钢筋
5)  prestressed steel
预应力钢筋
1.
The change method of prestressed steel isn t described basically in specialized works.
通过对预应力混凝土受弯构件的受力分析 ,提出了预应力混凝土受弯构件中预应力钢筋代换的基本方法。
2.
The laws of variation of mechanical behaviors with the temperature are investigated for prestressed steel and non_prestressed steel.
通过对21根Φ16月牙纹钢筋、45根12及8光圆钢筋、24根s5高强碳素钢丝高温下的力学性能试验,研究了预应力钢筋和非预应力钢筋的力学性能在高温下的变化规律。
6)  Prestressed reinforcement
预应力钢筋
1.
In bonded prestressed concrete beam,the depth of compression is not only related to the ratio of tension reinforcement,but also is related to the kinds and schemes of prestressed reinforcement and common reinforcement and the lever of stress of the prestressed reinforcement.
而在有粘结预应力砼梁中,受压区高度不仅跟受拉钢筋的配筋率有关,还跟预应力钢筋、非预应力钢筋的品种和匹配、以及预应力钢筋初始应力水平等因素有关。
2.
If the prestressed reinforcement is arranged in certain cylindrical surface, the formula can be simplified peatly and the equivalent load can be expressed by the geometric property of curve of the reinforement along the developed cylindrical surface.
如果预应力钢筋置于某个圆柱面内,则不但公式大为简化,而且可用圆柱展开面上钢筋曲线的几何特性表达等代荷载。
补充资料:预应力钢筋张拉设备
      使预应力混凝土结构里的钢筋产生并保持预应力的设备。分手动、电动和液压传动张拉机等。液压张拉机拉力大、重量轻,使用灵活方便。按钢筋张拉工艺有先张法和后张法两种。先张法用的夹具可以重复使用;后张法用的锚具将成为构件的一部分,不能取下再用。常采用不同的夹具来锚固各种钢筋,圆锥形夹具用于锚固直径12~16毫米的钢筋,镦头梳筋板夹具适用于板类构件中张拉低碳冷拔钢丝,波形夹具可成批张拉和锚固钢丝,螺杆锥形夹具则用于钢筋束的后张自锚。作业时,钢筋的一端锚固,另一端由张拉机通过夹具把钢筋夹紧张拉。穿心式张拉机作业时将钢筋穿入,打开前油嘴,由液压泵把高压油送入后油嘴,使张拉缸后退,利用尾部锚具将钢筋锚固并张拉。张拉到所需应力值后,关闭后油嘴。前油嘴进油,活塞向前推出,顶压锚塞,使钢筋锚固。回程时,活塞靠弹簧复位,完成张拉。
  
  管类构件可采用环向预应力缠筋机,在管坯上缠绕预应力螺旋钢筋(见图)。作业时,管坯由卡盘夹持,通过调直张紧滚轮在管坯上绕4~5圈应力不大的螺旋钢筋,此后液压缸使两侧的张紧轮分开,钢筋便张拉到预定的应力值。此时管坯旋转,并开动小车,管体上就连续绕上预应力螺旋筋。螺距的大小由小车的行走速度来控制。
  
  
  随着预应力构件生产批量的增加,一些专用的连续张拉设备得到发展,其特点是成组张拉效率高,需要的张拉力较小,可双向交叉配筋,张拉均匀,易于实现自动化生产。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条