说明：双击或选中下面任意单词，将显示该词的音标、读音、翻译等；选中中文或多个词，将显示翻译。 您的位置：首页 -> 词典 -> 钢筋束配置 1)  positioning of tendons 钢筋束配置 2)  arrangement of reinforcement 钢筋配置 3)  steel restraint 钢筋约束 4)  bundled bar 钢筋束 1. 25 in the code of GB50010-2002;and the design code of GB50010-2002 should be added the development length content on standard hooks and bundled bar when adding lightweight concrete,which can give reference for the revision of future structural design code. 25,同时建议增列标准弯钩和钢筋束的锚固长度及采用轻质混凝土时钢筋的锚固长度的规定。 5)  reinforcement ratio 钢筋配筋率 6)  steel bar matching 钢筋配料 1. This paper provides an algorithm based on simplex method for construction steel bar matching. 文章以单纯形方法为基础求解建筑钢筋配料问题。 补充资料：ANSYS SOLID65环向布置钢筋的例子  ANSYS SOLID65环向布置钢筋的例子! 一个管道，环向配筋率为1%，纵向配筋率为0.5%，径向配筋率为0.1%! 作者: 陆新征 清华大学土木系! FINISH/CLEAR/PREP7 !* ! 单元属性ET,1,SOLID65!* KEYOPT,1,1,0KEYOPT,1,5,0KEYOPT,1,6,0KEYOPT,1,7,1!* !实参数1：不同方向配筋R,1,2,.001, , ,2, .01, RMORE, 90, ,2,.005 ,90 ,90 , !材料属性!混凝土基本材料属性MPTEMP,,,,,,,, MPTEMP,1,0 MPDATA,EX,1,,30E2MPDATA,PRXY,1,,.2 !屈服准则 TB,MISO,1,1,5, TBTEMP,0TBPT,,0.0005,15TBPT,,0.001,21TBPT,,0.0015,24 TBPT,,0.002,27TBPT,,0.003,24!破坏准则 TB,CONC,1,1,9, TBTEMP,0TBDATA,,.5,.9,3,30,,TBDATA,,,,1,,, MPTEMP,,,,,,,, MPTEMP,1,0 !钢材基本属性MPDATA,EX,2,,200E3MPDATA,PRXY,2,,.27 !屈服准则TB,BISO,2,1,2, TBTEMP,0TBDATA,,310,2E3,,,, ! 管道内径和外径CYL4,0,0,3000, , , ,10000 CYL4,0,0,2000, , , ,10000 VSBV, 1, 2 ! 定义局部柱坐标CSWPLA,11,1,1,1,KWPAVE, 11 WPRO,,-90.000000, VSBW, 3 WPCSYS,-1,0 KWPAVE, 1 WPRO,,,-90.000000 VSBW,ALLESIZE,500,0,! 注意：设定单元局部坐标VATT, 1, 1, 1, 11!* VSWEEP,ALL/DEVICE,VECTOR,1/ESHAPE,1.0/REPLO ! 注意：红色代表最大配筋方向，绿色代表其次，蓝色表示最小配筋方向 说明：补充资料仅用于学习参考，请勿用于其它任何用途。 参考词条 ©2011 dictall.com