1) coefficient of excentralization
偏心系数
2) eccentricity coefficient
偏心距系数
1.
This paper defines such concepts as eccentricity coefficient, gravity center distance coefficient, pose probability.
定义了偏心距系数、重心距系数以及姿态概率等概念,为物料定向设计和提高上料效率提供了理论基础;通过试验得到了姿态概率计算公式,揭示了物料几何参数对姿态概率的影响规律。
3) eccentricity factor
偏心量系数
4) increase coefficient of bias distance
偏心距增大系数
1.
In view of the defects of increase coefficient of bias distance \%\% formula (GBJ10-89)in practice,considering the result of the limitstate alternative method resulted from the effect of the second coracte moments,by regression analysis and after much calculalion,the regression count expression formula of increase coefficient of bias distance is established.
针对现行混凝土结构设计规范ＧＢＪ１０－８９中，偏心距增大系数η计算公式在应用中存在的缺陷，在考虑二阶弯矩影响的有限元迭代法计算成果的基础上，通过大量计算，并运用回归分析，建立了钢筋混凝土受压构件η的计算表达式。
2.
To be in light of the fault of increase coefficient of bias distance η formula in current lightweight aggregate concrete standard in practice,considering the influence of two stepped moments by using the entire proceeding analyses theory,we reached the η of corresponding side and side deflection f and curvature φ of circular cross section biasing structure whose column ends are different.
针对轻骨料混凝土设计规范中偏心距增大系数η计算公式在应用方面有待于完善的问题,采用全过程理论分析并考虑二阶弯矩的影响,得出了在不同端弯矩下圆形截面偏压构件控制截面处截面曲率φ、侧向挠度f与相应的η值。
5) eccentricity amplifier
偏心距增大系数
1.
Taking into consideration the fact that all loads will not be woved in building construction when a structure is strengthened, we studied by the method of computer-test, how to calculate eccentricity amplifier of the slender concrete column strengthened non symmetrically with concrete to enlarge section subjected to axial load and bending moment.
采用计算机模拟试验方法，对非对称加大截面加固钢筋混凝土偏心受压中长柱的偏心距增大系数的计算问题进行了研究。
6) eccentric influence factor
偏心影响系数
1.
The eccentric influence factor α in the present tunnel specifications is used to express the extent of decreasing of compression strength of the eccentric loading plain concrete element in accordance with the increasing of the eccentric distances .
现行隧道设计规范用偏心影响系数α表征偏压构件抗压强度随偏心距增加而降低的程度，引入可靠度设计时必须知道此系数的统计特征及计算公式的不确定性。
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条