说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 二进制补码
1)  two's complement
二进制补码
2)  complementary offset binary
补码二进制
3)  two's complement modulo techniques
二进制补码取模
4)  two's complement subtract
二进制补码减法
5)  two's complement number
二进制补码数
6)  Binary Code
二进制码
1.
The absolute coder is introduced in two sides of the PLC programming and the interchange between Gray Code and Binary Code to explain how the function of angle measure is finished by PLC.
从格雷码与二进制码的互换和PLC编程两方面说明绝对值编码器怎样通过PLC实现角度测量的功能,指出了其在应用于港口装卸机械时应注意的事项。
2.
The method of shift-copy generating sequence by binary code copy information is presented.
介绍了以二进制码为复制信息,用平移复制生成序列的方法。
3.
The paper introduces the principle, the design thought and the software realization of converting for binary code to binary coded decimal code which are based on the CPLD FLEX10K of the Altera corporation and programmed in VHDL.
介绍了基于Altera公司的CPLD芯片FLEX10K ,以及利用VHDL语言实现多位二进制码转换成 84 2 1BCD码的原理、设计思路和软件实现。
补充资料:凹模、凸凹模工作型面加工工艺过程
1)备料。 n
    2)锻造。锻成长方形的坯料(每件留长工艺夹头)。 n
    3)热处理。退火。   n
    4)铣(刨)削。铣(刨)削六面成长方形模块。 n
    5)磨削。磨削上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度。 n
    6)钳工加工。用平板和划线盘按图划线,并打样冲眼;用钻头钻螺纹底孔;用圆柱销孔的预孔;用钻头钻挡料销让位孔;用钻头在中心处钻穿丝孔等;正、反面孔口倒角;凸凹模用钻头孔扩,保证刃口高度;攻螺纹;铰孔。n
  7)铣削。平口钳装夹工件;用的立铣刀铣削型孔至尺寸,保证深度。 n
   8)热处理。凹模工件淬硬至HRC60~64,凸凹模工件淬硬至HRC58~62。 n
   9)平磨。磨上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度至图要求;退磁。 n
   10)线切割。按图编制线切割程序,切割模型孔成形,留单面研磨余量0.005 mm。 n
   11)钳工加工。研光线切割面: n
   12)检验。 n复合冲裁模的装配应选择凸凹模作为装配基准件,先装下模部分,后装上模部分
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条