1) DSM (dynamic stiffness modulus)
动态刚度模数
2) dynamic stiffness coefficient
动态刚度系数
3) Dynamic stiffness
动态刚度
1.
Study on vertical dynamic stiffness and damp of running tire;
轮胎垂直滚动动态刚度和阻尼的研究
2.
Effect of pretension on dynamic stiffness of high-speed angular contact ball bearing
预紧对高速角接触球轴承动态刚度的影响
3.
The dynamic stiffness of pre-loaded hollow cylindrical roller bearing is analyzed.
对预载荷空心圆柱滚子轴承的动态刚度进行了分析。
4) dynamical stiffness
动态刚度
1.
And then the dynamical stiffness is obtained to evaluate the following characteristics of the loading system.
对国产MG－H型钢坯修磨机电液伺服加载系统建立了动态加载力的数学模型，并提出采用动态刚度来评价加载系统的跟随特性。
5) dynamic rigidity
动态刚度
1.
This article uses the control system theory, regards as the overflow valve is a control system, through the establishment of the relational model between hydraulic system pressure and the system current capacity, infers its dynamic rigidity function, then take enhancing the overflow valve the dynamic rigidity as the goal, with the aid of the MATLAB optimized to.
本文利用控制系统理论,将溢流阀看成为一控制系统,通过建立液压系统压力与系统流量的关系模型,推导其动态刚度函数,以提高溢流阀的动态刚度为目标,借助于MATLAB的优化工具箱进行结构参数优化。
2.
This paper worked on vibration analysis for different type gantry cranes,advanced a se-ries of practical calculation formula about vertical and horizontal dynamic rigidity of gantrycranes,added some calculation methods of the static and dynamic rigidity,enlarged proofingscopes of the static and dynamic rigidity for gantry cranes.
本文对不同类型门式起重机进行了振动分析研究，提出一系列门式起重机垂直与水平动态刚度的实用计算公式，增补了静、动态刚度的计算方法，扩大了门式起重机静、动态刚度的校核范围，针对门式起重机的特点和对现有研究资料的分析，推荐出静，动态刚度的控制值，为实现门式起重机的动态设计创造了有利条件。
3.
Through the experiment and the related project data,combining with the finite element that simulated the behavior of the bending steel pipe concrete,we can obtain the effect to the rigidity factor from materials and sizes,and get dynamic rigidity of steel pipe concrete structures\' mathematical expression.
通过试验和相关工程数据,结合有限元模拟钢管混凝土构件受弯时的力学行为,得出材料、构件尺寸等对刚度系数的影响,并得到钢管混凝土构件动态刚度的数学表达式。
6) zero dynamic stiffness
零动态刚度
1.
The paper provides a principle analysis of the passive vibration isolator using zero dynamic stiffness,which demonstrates the vibration in the low frequency range is available based on the zero dynamic stiffness principle and the method of passive vibration isolation.
论文给出了零动态刚度被动减振系统的理论分析,论证了基于零动态刚度原理和利用被动减振的方法,可实现低频频率范围内的减振。
补充资料：轧机刚度系数
轧机刚度系数
rigidity coefficient of rolling mill
zhalj gongdu xishu轧机刚度系数(rigidity eoeffieient of rollingmill)使轧机产生纵向单位弹性变形所需施加的轧制力。其几何意义为轧机弹性曲线直线段的斜率，记作 dP K~~共气 “m ds式中d尸为轧制力增量;ds为辊缝增量;Km为轧机刚度系数，其量纲为kN/mm。因此，某一轧机的刚度系数可根据轧机的弹性曲线的斜率计算确定。实际上，由于轧制时轧棍和整个车L机在负荷作用下温度升高，辊缝发生变化而成为一个变值，轧辊的圆度和安装偏差会造成轧件的纵向厚度偏差呈高频周期性变化，轧件、一公淤叮派李点- 翻~香爪~~咋今粉~ 轧钢机按机架排列分类 a一单机架;吞一横列式;一顺列式;d一棋盘式;~半连续式;了一连续式宽度也会影响轧辊的弯曲弹性变形等，所以为了提高轧件厚度控制的精确度，轧机的刚度系数一般都通过现场实测方法得到。但也可以在用解析方法分别算出轧辊的刚度系数K，、机架的刚度系数KZ、安全臼的刚度系数K3、压力传感器的刚度系数K4等之后，按下式计算 1 K，~— 1 .1 .1 .1 分+分十含+亡 K:1 KZ’K3’K4因此，K。又称等效刚度。 (赵以相)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条