说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 基波分量,基本分量
1)  fundamental component
基波分量,基本分量
2)  elementary component
基本分量
3)  fundamental component
基波分量
1.
A real time method for detecting the fundamental component of the line voltage under distorted circumstance is proposed in the paper.
提出了一种在电网电压畸变情况下依然适用的电网电压基波分量的实时检测方法。
2.
Calculating the fundamental component from fault transient signals quickly is a crux of microprocessor protective relay to operate in time.
提出了短窗积分提取基波分量法 ,即首先选定采样短窗及其上的一族基函数 ,由此建立积分线性方程组 ,通过解方程组得出基波分量的值 ,并给出了理论推证。
3.
This paper discusses the method by which fundamental components are calculated with Wallis function algorithm in computer relay protection, calculates the effect of nonperiodic components on the accuracy of Wallis function algorithm, probes into the measures removing the effect of nonperiodic components, and compares Wallis function algorithm with Fourier algorithm.
本文论述沃尔什函数算法在微机继电保护中计算基波分量的方法,计算非周期分量对沃尔什函数算法精度的影响,探讨消除非周期分量影响的措施,并对沃尔什函数算法与傅里叶算法进行比较和分析。
4)  Intrinsic mode function
基本模式分量
1.
The vibration signal is decomposed into several intrinsic mode functions (IMFs) by EMD, and the fault information is extracted from the IMFs containing modulated signals, which then is effectively separated by EMD, thereby the signal to noise ratio (SNR) of diagnosis signal is impro.
首先,对复杂的振动信号进行经验模式分解,得到若干个基本模式分量,再对包含调制信号的基本模式分量进行包络分析以提取故障信息。
2.
Empirical mode decomposition(EMD) is a signal processing technique to decompose data set into several intrinsic mode functions(IMF) by a sifting process.
经验模式分解(EMD)通过筛分过程将原始信号分解成若干个基本模式分量(IMF),可看作无需预设带宽的自适应高通滤波方法。
3.
First we decompose the time series analyzed using local wave decomposition, generating a few intrinsic mode functions, then predict all the intrinsic mode functions using AR mode respectively, lastly reconstruct the pre.
用局域波分解法对待预测的时间序列进行经验模式分解,产生多个基本模式分量,对各个分量分别进行AR模型预测,然后重构各个预测值。
5)  elementary constraint component
基本约束分量
6)  Intrinisic mode function(IMF)
基本模态分量
补充资料:对称分量
      由不对称三相相量分解而得的对称三相相量。一组不对称三相相量凔、妋、凗,当三者之和不为零(即凔+妋+凗≠0)时,可以分解成三组对称三相相量,它们分别是:零序分量,记为凔0,妋0,凗0;正序分量,记为凔1,妋1,凗1;负序分量,记为凔2,妋2,凗2。由于三相电力系统中有三相交流电机、三相输电线等三相电路元件,它们的电路参数在对称的运行条件下较便于确定,因而将非对称三相相量分解为三组对称分量便可分别考虑在每一相序的电压、电流作用下三相电路的工作情况,然后根据叠加定理得到三相电路的工作情况。
  
  零序分量如图1所示,其特征是3个相量大小相等且同相。妋0=凔00=凔0正序分量如图2所示,其特征是3个相量大小相等但不同相。三者按妋1滞后凔1,凗1滞后妋1,凔1又滞后凗1的顺序互差120°,即
  妋1=a211=a凔1
  式中
  
   
  负序分量如图3所示,其特征类似正序分量,也是3个相量大小相等但不同相。不过,此时3个相量是按凗2滞后凔2,妋2滞后凗2,凔2又滞后妋2的顺序互差120°,即妋2=a凔22=a22三组对称分量与原不对称三相相量的关系如下:不对称三相相最可以是三相电压相量,也可以是三相电流相量。在三相不对称电路中,有的不对称电压相量和不对称电流相量只有两组对称分量。例如,不对称线电压相量,因必须满足KVL,即妭AB+妭BC+凗CA=0,故只含有正序对称分量和负序对称分量。
  
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条