1) plastic analysis
塑性状态分析
2) Dynamic pushover
动态弹塑性分析
4) plastic analysis
塑性分析
1.
Approximate establishment of pushover curve for frame with supplemental viscoelastic dampers on the basis of plastic analysis;
基于塑性分析近似构建附加黏弹性阻尼器框架结构推覆曲线
2.
By comparing the ways of plastic analysis, the plastic moment coefficient and load coefficient are used to illustrate the collapsing load formula of mobile-structure.
本文通过对塑性分析方法比较,采用了塑性弯矩系数和荷载系数来表达机构破坏荷载公式。
3.
In the strain analysis,it shows that the thickness of steel plate keeps constant when the steel plate is rolled into a cylinder in the process of bending, and the stress- strain curve of the perfect stiffplastic model is suited to the plastic analysis of the cylinder of pressure vessels when the steel plate is made int.
应变分析表明理想刚塑性模型的应力一应变曲线能适用增量理论对筒体的成形进行塑性分析,且简体在弯卷成形时保持钢板的厚度恒定不变;应力分析表明筒体在弯卷成形中产生的“初始应力”是不对称的。
5) plasticity analysis
塑性分析
1.
A case study shows that a remarkable increase in the load limit through plasticity analysis to elasticity analysis.
将圆形板极限分析的结果应用于圆柱形塔基础的底板分析,通过实例分析说明塔基础底板的荷载,塑性分析计算比弹性计算的值有较大幅度的提高。
补充资料:弹—塑性变分原理
弹—塑性变分原理
elastic-plastic variational principle
tan一suxing bionfen yuanll弹一塑性变分原理(elastie一plastic variation-al Principle)适于弹一塑性材料的能量泛函的极值理论。包括最小势能原理和最小余能原理。塑性加工力学中常用最小势能原理。变形力学问题的能量解法和有限元解法都基于最小势能原理。最小势能原理有全量理论最小势能原理和增量理论最小势能原理。 全量理论最小势能原理在极值路径(应变比能取极值的路径)下运动许可的位移场u‘中,真实的位移和应变使所对应的总势能取最小,即总势能泛涵巾取最小值,其表达式为”一0,’一万〔A(一,一关一〕dV一好多!一‘“ (l)式中“:为位移;户:为外力已知面上的单位表面力;关为体力;A(气)为应变比能。 A(勒)随材料的模型而异。对应变硬化材料(图a), E严_‘_‘_ A(乓r)一二丁二一气助+{刃(r)dr(2) 6(1一2刃~一“‘J一、-一、- 0式中E,,分别为弹性模量和泊松比;艺一硫瓜,r一掩不万,,,f,一,一音。魔。,,一,一,一音。*。!,;。f,为克罗内克(L.Kroneeker)记号,i=夕时a,一l,i笋少时民,一。,把式(2)代入式(1)便得到卡恰诺夫(几·M·Ka、aHoe)原理x的表达式。i厂:八 I’—几 I’一 ab 乞一乏(r)关系图 a一应变硬化材料;占~理想塑性材料 对于理想塑性材料(图b), 艺~ZGr(r
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条