说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 准尺寸孔
1)  dimensioned hole
准尺寸孔
2)  pore size
孔隙尺寸
1.
Pore-size distribution function gives quantitative characterization of the pore sizes distribution while local porosity distribution function can offer qualitative analysis of the core's homo.
研究表明,连通孔隙体积比能够准确描述岩心中孔隙的整体连通性;孔隙尺寸分布函数可以定量表征岩心孔隙的分布;局部孔隙度分布函数不但可以对岩心中孔隙、岩石骨架的最大发育规模进行定量评价,而且能够对岩心均质性进行定性分析;测量单元标准差分布曲线可以为岩心均质性分析时测量单元边长的合理选取提供重要依据;借助局部渗流概率函数能够对岩心的连通性能及是否为各向同性作出合理的定性判断。
2.
Based on MATLAB software, the cross sectional and longitudinal pore size distributions of granular ore media were calculated to investigate the evolution of granular ore media\'s pore size distribution during heap leaching and its influences on permeability.
根据X射线CT技术无损伤地探测细菌浸出前、后矿岩散体介质孔隙结构特征,利用MATLAB环境编写程序对矿岩散体介质颗粒间横向及纵向孔隙尺寸分布进行统计,研究细菌浸出过程中矿岩散体粒间孔隙尺寸演化规律及其对溶浸液渗流特性的影响。
3.
The influences of parameters such as the sample pressure,nickel content and titanium powder size on pore size,pore uniformity and microstructure were studied.
以镍粉和钛粉为原料,采用自蔓延燃烧合成技术制备了多孔NiTi形状记忆合金,研究了压坯压力、镍含量、钛粉粒径等参数对合金孔隙尺寸、孔隙均匀性和显微组织的影响。
3)  cell size
泡孔尺寸
1.
Extruded polypropylene foam with low open cell content, high cell density, small and uniform cell size was prepared via blending conventional linear polypropylene with a small amount of high melt strength polypropylene (HMSPP).
通过添加少量高熔体强度的支化聚丙烯,制备了开孔率低、泡孔密度大、泡孔尺寸小、泡孔分布均匀的聚丙烯挤出发泡材料;通过发泡材料断面的SEM分析,比较了成核剂类型和粒径对泡孔密度和尺寸的影响。
4)  size of struts
孔筋尺寸
1.
A more reasonable method, in which coating properties were evaluated through measuring the size of struts of green bodies and uniformity of slurry distribution in the struts of green bodies, was employed.
采用有机泡沫浸渍法制备碳化硅泡沫陶瓷时,通过对聚氨脂泡沫进行不同改性剂的表面处理来改善其挂浆性能,利用一种更加合理的表征方法,即测量挂浆后泡沫陶瓷素坯孔筋尺寸和表征孔筋挂浆后形貌来衡量挂浆性能。
5)  dimensions of the window
窗孔尺寸
6)  The dimension between holes
孔系尺寸
补充资料:工程图标准尺寸及坐标尺寸

标准标注类型,是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。


· 3.2 标准标注到坐标标注的转换


注意: 转化为坐标标注的尺寸必须是线性标注的,下列尺寸不能转化为坐标标注:


 



  • 被显示成线性尺寸的直径
  • 中心线尺寸

 



  1. 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base.
  2. 选择作为参考基准线的尺寸
  3. 选择基准的引出线,该点为0点
  4. 选择 MOD DIM TYPE > Lin to Ord .
  5. 选择线性尺寸:注意:必须选择具有相同基准的尺寸

========>>>>

· 3.3 由坐标标注到标准标注的转化

1. 选择 DIM PARAMS > Diam Dim Type .


2.点击Ord to Lin


3.选择尺寸即可

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条