1) axle load
轴荷
1.
In order to calculate the axle load of multi-axle vehicles,the multi-axle vehicles\'vertical axle loads mathematical model is established and a new calculation method is proposed.
为计算多轴汽车的轴荷,建立了多轴汽车的轴荷模型,提出了多轴汽车轴荷分配计算的新方法。
2.
Base on the theory calculation and experience, expound and introduce the means that multi axis ( three axis or more) special purpose vehicle chassis axle load is estimated in scheme design stage.
在理论计算和实践经验的基础上 ,论述和介绍了多轴 (三轴及三轴以上 )专用汽车底盘方案设计阶段轴荷估算的方
2) axial load
轴向载荷
1.
Analysis of axial load influence on mechanics characteristic of ocean deep water drilling riser;
轴向载荷对海洋深水钻井隔水管力学特性的影响分析
2.
Stability of pipe conveying fluid under axial load;
轴向载荷输流管道的稳定性分析
3.
We have deducedthe simplified mechanics model for calculating frictional resistance and axial load when lowering pipe string or lifting pipe string in a inclined well.
在斜井中 ,考虑了方位角的变化 ,建立管柱受力平衡方程 ,推导出斜井中下管柱和提管柱时摩擦阻力和轴向载荷的简化力学模型 ,分析计算了下管柱和提管柱时摩擦阻力、轴向载荷以及管柱轴向变形等重要参数的解析公式。
3) uniaxial load
单轴载荷
1.
Experimental study of the NMR characteristics in rock under uniaxial load;
单轴载荷下岩石核磁共振特征的实验研究
2.
In this paper,acoustic wave technology was used to study the damaged characteristics of salt rock under uniaxial loading and the effect of damage on dissolution to reveal the parietal injury dissolved characteristics in salt cavity construction period.
采用声波技术研究盐岩在单轴载荷条件下的损伤特征,并对受损盐岩进行溶解试验分析,以此来分析盐穴建造期盐岩的损伤溶蚀机制。
4) axial load
轴向荷载
1.
The deformation,axial load,distribution of shaft r.
结果表明,由于夯实水泥土桩体强度的限制,荷载沿桩身的传递限定在浅层一定范围内,桩身变形、轴向荷载、桩侧摩阻力分布主要发生在此范围内,而且变化梯度较大。
2.
In order to study the distribution of stress concentration factor(SCF) along the welded toes of the joint under axial load(AX) and in-plane-bending load(IPB),full-scale completely overlapped K-joint specimen has been tested.
对大型完全叠接K型管节点试件分别承受轴向荷载和平面内弯曲荷载时的应力集中系数进行了实验测试,通过数值分析,得到了完全叠接K型管节点承受这两种基本荷载作用时焊缝周围的应力集中系数分布情况,分析结果与实验数值相吻合,结果表明在轴向荷载和平面内弯曲荷载作用下,斜管与叠管交接处的应力集中现象比较严重,而主管相对安全,这对指导工程设计是非常有益的。
5) Axially loaded
轴向负荷
1.
Objective To evaluate the effects of axially loaded MR imaging on the lumbar spinal canal,and its clinical value.
【目的】评估仰卧位轴向负荷腰椎MRI检查对椎管的影响及其临床意义。
2.
ResultEach intervertebral angle in conventional CT scanning and in axially loaded CT scanning was as follows: L1/2 0.
目的通过采用腰椎轴向负荷压力装置,比较健康志愿者腰椎常规CT扫描与轴向负荷CT扫描所得图像中椎体间成角及椎间盘高度的差别,探讨轴向负荷CT扫描的作用,并分析其在腰椎间盘突出症CT诊断中的应用。
6) bearing load
轴承负荷
1.
The matrix equation of bearing load distribution in multi\|support rotor\|bearing system is deduced by using a transfer matrix method.
利用传递矩阵法建立了多支承转子轴承负荷分配关系的矩阵方程 。
2.
This paper presents a comprehensive analyzing method of strain measurement and Riccatimatrix for bearing loads of marine shafting.
论述了船舶轴系轴承负荷的应变片检测与Ｒｉｃｃａｔｉ矩阵综合分析方法，该法不受尾轴轴承数量和轴系边界条件的限制，可用轴系在便于设置测点处测得几个断面的弯矩，推算出各个轴承的轴承负荷及各个轴段的弯曲应力。
3.
The change of bearing load on rotor -bearing system wouldincur great vibaration and disastrous accidents.
多支承转子-轴承系统是大型旋转机械的核心部件，其轴承负荷发生变化将引起转子系统的剧烈振动，导致重大事故的发生。
补充资料：单轴各向异性
单轴各向异性是磁晶各向异性的最简单形式，即自发磁化的稳定方向（或易磁化方向）平行于一特殊晶轴。如六方晶系钴的自发磁化方向平行于 C轴(见晶体结构)，这就表现出强的单轴各向异性。磁性材料的单轴各向异性值一般都低于其磁晶各向异性值，为103erg/cm3量级。磁性材料经磁场热处理或强的冷加工而产生的感生各向异性，都属于单轴各向异性。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条