1) flexural rigidity of section
截面弯曲刚度
2) warping rigidity of section
截面翘曲刚度
3) bending stiffness out of plane
面外弯曲刚度
4) bending rigidity
弯曲刚度
1.
Discussion on bending rigidity anisotropy of fabrics;
织物弯曲刚度各向异性探讨
2.
Bending deformation and bending rigidity of mechanical components;
机械构件的弯曲变形与弯曲刚度
3.
Approach to calculating bending rigidity of rubber-reinforced track of tractors and its experimental verification;
拖拉机橡胶钢筋履带弯曲刚度计算方法与试验验证
5) bending stiffness
弯曲刚度
1.
Applied investigation on the effects of bending stiffness of machine bed's simulating parts on its thermal geometrical precision;
机床床身模拟件的弯曲刚度对其热态几何精度影响规律的应用研究
2.
Analysing parameters of bending stiffness of FRP and designing its structure;
FRP弯曲刚度的参数分析与结构设计
3.
Engineering algorithm on bending stiffness of elastic rubber bushing of car suspension;
轿车悬架弹性橡胶衬套弯曲刚度的工程算法
6) Bend stiffness
弯曲刚度
1.
The mechanical models of bend stiffness and bend strength of the pallets girder and deck were established.
通过分析木托盘在均布载荷作用下的受力变形情况,建立了木托盘梁和铺板的弯曲强度和弯曲刚度的力学模型,提出了托盘弯曲强度和刚度的条件。
补充资料:弯曲工艺的概念及弯曲件
1.弯曲工艺:是根据零件形状的需要,通过模具和压力机把毛坯弯成一定角度,一定形状工件的冲压工艺方法。
2.弯曲成形工艺在工业生产中的应用:应用相当广泛,如汽车上很多履盖件,小汽车的柜架构件,摩托车上把柄,脚支架,单车上的支架构件,把柄,小的如门扣,夹子(铁夹)等。
弯曲的基本原理:以V形板料弯曲件的弯曲变形为例进行说明。其过程为:
1. 凸模运动接触板料(毛坯)由于凸,凹模不同的接触点力作用而产生弯矩, 在弯矩作用下发生弹性变形,产生弯曲。
2. 随着凸模继续下行,毛坯与凹模表面逐渐靠近接触,使弯曲半径及弯曲力臂均随之减少,毛坯与凹模接触点由凹模两肩移到凹模两斜面上。(塑变开始阶段)。
3.随着凸模的继续下行,毛坯两端接触凸模斜面开始弯曲。(回弯曲阶段)。
4.压平阶段,随着凸凹模间的间隙不断变小,板料在凸凹模间被压平。
5. 校正阶段,当行程终了,对板料进行校正,使其圆角直边与凸模全部贴合而成所需的形状。
弯曲变形的特点: 弯曲变形的特点是:板料在弯曲变形区内的曲率发生变化,即
弯 曲半径发生变化。从弯曲断面可划分为三个区:拉伸区、压缩区和中性层。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条