说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 配对误差
1)  Matching Error
配对误差
2)  assembling error
装配误差
1.
The assembling errors for the stabilization mechanism can significantly influence the performance of sight-line stabilization.
稳定机构的装配误差是造成视轴偏差的重要误差源。
2.
The assembling error of three-axis turntable is unavoidable during assembling process,which is one of the primary system error sources.
作为造成三轴转台最终误差主要的系统误差源,装配误差在装配过程中难以避免。
3)  Error distribution
误差分配
1.
On the error distribution and its analysis in the physical experimental design;
物理实验设计中的误差分配和误差分析
2.
Based on the error distribution requirement in the measurement for attached conducting wire in engineering survey the calculating procedure for the measurement of attached conducting wire is deduced from different observing angle and two useful formulas that can be directly applied to the calculation are obtained.
根据工程测量中附合导线测量的误差分配需要,依照观测角的不同,推导附合导线测量的计算过程,并推导出两个实用计算公式。
4)  Registration error
配准误差
1.
An effective LUCCD method to decrease the effect of registration error;
一种有效的减弱配准误差影响的LUCCD方法
2.
When using rectangles as the target,it s difficult to measure the Modulation Transfer Function(MTF) of the space camera accurately because of the registration error between the image of the target and the pixel of the CCD at the initial sampling.
在采用矩形靶标测量航天相机系统MTF时,由于采样初始时刻靶标像与CCD像元间存在配准误差,因此给准确测量系统MTF带来很大困难。
3.
Methods After analysis of elements of the matching algorithm, the different registration algorithm performance are evaluated by the use of a comprehensive registration error based on C ++ to be realized, which can compare with the evaluation results of traditional target registration error.
方法:分析各配准要素的算法原理后,基于C++加以实现,提出使用综合配准误差来评价不同配准算法的性能,并与传统目标配准误差的评价结果作对比。
5)  assembly error
装配误差
1.
Finally the assembly error is also analyzed.
同时,还对该装置的装配误差进行了分析。
2.
Tooth contact analysis is developed forthe TI worm gearing with assembly errors.
实现了TI蜗杆传动的三维参数化设计,对含有装配误差的TI蜗杆传动的啮合接触情况进行了分析。
6)  mismatch error
失配误差
1.
Method of eliminating of mismatch error in microwave power measurement;
微波功率测量中消除失配误差的方法
补充资料:Pro/E 关于装配图的工程图
在装配图中,我们可以显示或隐藏(erase)装配或零件的尺寸,可以装配视图中直接在独立的元件(components)间建立尺寸。注意如下事项:可以用注解(note)的形式显示装配中特征的参数,但不能显示零件的参数要显示或改变装配图中的尺寸,必须保证相关的装配模型也在内存中当我们在模型中隐藏(suppress)了零件或子装配时,
在装配图中,我们可以显示或隐藏(erase)装配或零件的尺寸,可以装配视图中直接在独立的元件(components)间建立尺寸。注意如下事项:
可以用注解(note)的形式显示装配中特征的数,但不能显示零件的参数
要显示或改变装配图中的尺寸,必须保证相关的装配模型也在内存中
当我们在模型中隐藏(suppress)了零件或子装配时,在工程图中相关的内容也被隐藏,当恢复些元件时,相关内容也同时被恢复(Resume),这些内容包括:

尺寸位置
表面粗糙度放置位置
注解中的参数文本以及符号的特例
刨面线
刨面位置的参考边界
轴线
边以及参考平面的显示信息
和零件相关的绘制几何体的公差,等等
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条