1) PET beer bottle
PET啤酒瓶
1.
The application of finite element in the mechanics analysis on PET beer bottle was introduced.
介绍了有限元法在PET啤酒瓶力学分析中的应用,在对PET啤酒瓶结构分析的基础上,利用ANSYS有限元分析软件对PET啤酒瓶进行仿真应力分析,进而给出了厚度对PET啤酒瓶力学性能的影响,为PET啤酒瓶的结构优化设计和推广提供方法和依据。
2) beer bottle
啤酒瓶
1.
Current status and prospects of polyester beer bottles;
聚酯啤酒瓶研发现状及应用展望
2.
The application for the projecting the manufacture date on to the beer bottle;
在啤酒瓶上射码生产日期的应用
3.
The Research on Vision-based Beer Bottle Inspector;
啤酒瓶视觉检测机器人研究
3) bottled beer
瓶装啤酒
1.
Quality control during the packaging of bottled beer;
瓶装啤酒包装过程中质量控制因素的探讨
2.
Through the comparison of the effects of flash pasteurization, normal pasteurization and membrane filtration on the freshness of bottled beer, the key technical parameters and relative control modes for flash pasteurization were investigated.
通过对瞬时巴氏杀菌、隧道式喷淋巴氏杀菌、膜过滤啤酒技术对瓶装啤酒生产新鲜度的研究比较,研究了瞬时巴氏杀菌用于瓶装啤酒生产的关键工艺参数以及控制模式。
3.
Whether packing quality of beer is good plays an important part in its quality and outlook Fine management of packing quality is very important to the business The passage has done research into the instructions for packing quality of bottled beer And it has also studied the methods of quality management of packing proces
本文对瓶装啤酒包装质量的具体要求以及包装过程主要环节质量管理与控制的方法进行了探
4) bright bottle beer
白瓶啤酒
1.
Study on the technology of 8°BX bright bottle beer;
白瓶啤酒酿造工艺的研究
5) Beer bottles
啤酒瓶
1.
The Study on Life Cycle Assessment of Beer Bottles for Special Purpose;
专用啤酒瓶生命周期评价研究
2.
Now the main courses of beer bottles exploding are beer bottle's quality question and the consumer drinking improper .
啤酒瓶爆炸伤人于伤者痛苦,于厂家事与愿违。
补充资料：PET
聚对苯二甲酸乙二醇酯是由对苯二甲酸二甲酯与乙二醇酯交换或以对苯二甲酸与乙二醇酯化先合成对苯二甲酸双羟乙酯，然后再进行缩聚反应制得。属结晶型饱和聚酯，平均分子量(2-3)×104，重均与数均分子量之比为1.5-1．8。相对密度1.368．熔点225℃，流动温度243℃：，玻璃化温度80℃，马丁耐热80 ℃，热变形温度98℃(1. 82MPa)，分解温度353℃。具有优良的机械性能．刚性高．硬度大，吸水性很小，尺寸稳定性好。韧性好，耐冲击、耐摩擦、耐蠕变。耐化学性好，溶于甲酚、浓硫酸、硝基苯、三氯醋酸、氯苯酚，不溶于甲醇、乙醇、丙酮、烷烃。使用温度-100～120℃。
弯曲强度 148-310MPa
吸水性 0. 06％-0.129％
冲击强度 64.1-128J／m
洛氏硬度 M 90-95
伸长率 1.8％-2.7％
弯曲强度 148-310MPa
吸水性 0. 06％-0.129％
冲击强度 64.1-128J／m
洛氏硬度 M 90-95
伸长率 1.8％-2.7％
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条