说明：双击或选中下面任意单词，将显示该词的音标、读音、翻译等；选中中文或多个词，将显示翻译。 您的位置：首页 -> 词典 -> 屈曲温度 1)  buckling temperature 屈曲温度 1. Some observations were: the greater the axial restraint stiffness,the lower the buckling temperature and the failure temperature;the greater the axial restraint stiffness,the smaller displacement after the column\'s buckling;the failure temperature of a restrained column is usually higher than the buckling temperature. 约束刚度大小对钢柱抗火性能的影响包括:约束刚度比大的钢柱,其屈曲温度和破坏温度均较低;钢柱屈曲后,约束刚度比大的钢柱在变形较小时即可达到新的平衡位置;约束钢柱的破坏温度一般高于其屈曲温度,且随轴向约束刚度比的增大,破坏温度与屈曲温度之差增大。 2. The effects of the restraint stiffness ratio,the axial load ratio and the column slenderness on the buckling temperature and failure temperature of a restrained H-section steel column under axial load in fire were studied with a calibrated finite element method(FEM) model. 利用验证的有限元模型分析了轴向约束刚度比、轴力荷载比和钢柱长细比对火灾下轴心受压H形截面约束钢柱屈曲温度和破坏温度的影响,给出了其屈曲温度和破坏温度的计算方法。 2)  buckling strength 屈曲强度 1. Study and Realization on Assessment of Buckling Strength of Ship Structural Plate with Corrosion Damnification; 腐蚀损伤船体结构屈曲强度评估方法研究与实现 2. Structure optimum of hydraulic hatch cover based on corrosion aspect and buckling strength 考虑腐蚀影响与屈曲强度的液压折叠式舱口盖结构优化 3. The buckling strength of the stitched composite laminates under the in-plane compressive load is predicted. 基于包含若干分层的缝纫复合材料层合板在面内压缩载荷作用下发生屈曲破坏的机理,即厚度方向上的缝纫线被拉断,把缝纫线的极限伸长率作为层合板屈曲破坏的控制参数,采用能量的方法建立了用于预测缝纫复合材料层合板屈曲强度的理论模型。 3)  Hi-flexion 高屈曲度 1. Comparison of Hi-flexion and Total Condylar Prosthesises in Total Knee Arthroplasty Preliminary Clinical Results; 高屈曲度假体与全髁型假体早期临床疗效比较 4)  flexion range 屈曲角度 1. The flexion range of knee joint could be seen as the most important factor to evaluate the effect of total knee arthroplasty. 膝关节屈曲角度是评定全膝关节置换手术效果的重要因素。 5)  waviness [英]['weivinis]  [美]['wevɪnɪs] 屈曲度 6)  hyperflexion 屈曲过度 补充资料：表光合强度(见光合强度) 表光合强度(见光合强度) forecast of sowing or transplanting time b iaoguanghe qiangdu表光合强度见光合强度 说明：补充资料仅用于学习参考，请勿用于其它任何用途。 参考词条 ©2011 dictall.com