说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 缩径挤压
1)  Ironing Process
缩径挤压
1.
Analysis of Ironing Process for High Strength Ti Alloy
高强钛合金缩径挤压成形机理分析
2)  stretching lateral extrusion
缩径侧向挤压
1.
According to the moving direction relations between punch and workpiece,a new definition of lateral extrusion has been put forward,at the same time,the new concepts of compressing lateral extrusion,equal-cross section lateral extrusion and stretching lateral extrusion have been put forward too.
根据挤压方向和挤出方向之间的相互关系,对侧向挤压这一概念赋予了新的定义,同时也提出了扩径侧向挤压、等径侧向挤压和缩径侧向挤压3个新概念,进一步给出了等径侧向挤压真应变的计算公式,并指出等径侧向挤压法是制备块状细晶材料的一种好方法。
3)  Squeeze [英][skwi:z]  [美][skwiz]
压缩,挤压
4)  radial extrusion
径向挤压
1.
Technical Study of Radial Extrusion Forming on the Super-Long Odd Shafts based on Multiple Directions Extrusion
基于多向挤压的超长异形轴径向挤压工艺研究
2.
The radial extrusion technological process of the internal thread spline was studied and a set of extrusion mould suitable for the forming of the internal thread spline in the guide bush.
以汽车单向器导向筒内螺旋花键为研制对象 ,对内螺旋花键的径向挤压工艺进行了研究 ,设计了1副适合于导向筒内螺旋花键径向成形的挤压模。
3.
The warm radial extrusion of internal ring with inclined groove is introduced in this paper.
介绍了斜槽内环零件的温径向挤压工艺及三瓣模的设计、模具结构及主要零件的设计及选材。
5)  diameter-expanded extruding
扩径挤压
1.
The analysis on tube-shaped object in the course of diameter-expanded extruding;
筒形件扩径挤压过程分析
6)  pressing route
挤压路径
1.
In order to determine the influence of both pressing route and pass on the microstructures and tensile properties of the Mg-Mn-Zn-Ce alloy,equal channel angle pressing(ECAP) was conducted under different pressing routes for different passes.
为了确定挤压路径和挤压道次对Mg-Mn-Zn-Ce合金的显微组织及拉伸性能的影响,采用不同挤压路径对Mg-Mn-Zn-Ce合金进行了不同道次的等通道转角挤压(ECAP)。
补充资料:侧向挤压


侧向挤压
sideway extrusion

CeXIQng』lyo侧向挤压(sideway extrusion)制品流出方向与挤压杆运动方向成900的挤压方法,也称横向挤压。可分为单向侧向挤压和双向侧向挤压(如图所示)。侧向挤压的特点是:挤压模与锭坯轴线成9扩放置,挤压力与锭坯轴线方向一致,这种金属流动机构使制品遍纂 。b今簿黔 侧向挤压示意图 a、乙单向侧向挤压;‘一双向侧向挤压 1一挤压筒;2一挤压杆;3一模子;4一锭坯;5一挤压制品的纵向力学性能差异最小;变形程度大,挤压比可达100:1,制品强度高;要求模具和工具具有高的强度及刚度。该方法被用来制造高质量的航空用阀的弹簧。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条