说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 聚对苯二甲酸乙二醇酯/聚对苯二甲酸丁二醇酯
1)  poly(ethylene terephthalate)/poly(butylene terephthalate)
聚对苯二甲酸乙二醇酯/聚对苯二甲酸丁二醇酯
2)  Poly(ethylene glycol terephthalate) and poly(butylenes terephthalate)copolymer
聚乙二醇对苯二甲酸酯/聚对苯二甲酸丁二醇酯
3)  CGP
聚对苯二甲酸乙二醇酯-聚对苯二甲酸丁二醇酯-聚丁二醇共聚酯
4)  PEGT/PBT
聚乙二醇/聚对苯二甲酸丁二醇酯
5)  PBT
聚对苯二甲酸丁二醇酯
1.
The fractography of PBT at different temperatures was analyzed, the fractography features of PBT fracture arc stripe were concluded, the total number, dimension of feature zone and roughness of arc stripe were studied in quantification, the mechanism of arc pattern was also discussed.
分析了不同温度下聚对苯二甲酸丁二醇酯(PBT)的断口形貌,总结了PBT断口弧形条纹的形貌特征,定量研究了弧形条纹数量、特征区尺寸及表面粗糙度的变化规律,并对其形成机理进行了探讨。
2.
POE-g-GMA and PBT/POE-g-(GMA-coSt) were prepared by melt grafting in the twin screw extruder.
在双螺杆挤出机上采用熔融接枝法制备了POE-g-GMA和POE-g-(GMA-co-St),考察了POE、POE-g-GMA和POE-g-(GMA-co-St)对聚对苯二甲酸丁二醇酯(PBT)的增韧作用。
3.
The effect of the mass content of glass microbeads (GB) on the melt rheological and mechanical properties of PBT/short glass fiber(GF)composite was studied.
研究了玻璃微珠(GB)用量对聚对苯二甲酸丁二醇酯(PBT)/短玻纤(GF)复合材料熔体流变性和力学性能的影响。
6)  polybutylene terephthalate
聚对苯二甲酸丁二醇酯
1.
Depolymerization experiments of polybutylene terephthalate (PBT) in supercritical methanol were carried out in a batch-type reactor with the reaction temperature of 453~583K and reaction time of 5~90 min.
在高压间歇无搅拌反应器中研究了聚对苯二甲酸丁二醇酯(PBT)在高温甲醇溶液中的降解行为,通过对降解产物的各种定性和定量的分析,提出了超临界甲醇降解PBT的机理为在甲醇的作用下聚合物分子链的随机断裂和酯交换反应双重作用下发生的降解反应,建立了降解-反应模型。
2.
The prepolymer of polybutylene terephthalate (PBT) was grafted onto the surface of nano-SiO2 partides by polycondensation for modification.
将得到的改性粒子填充聚对苯二甲酸丁二醇酯,检测填充前后树脂的性能。
3.
Kinetics of thermal degradation of polybutylene terephthalate(PBT) was investigated using the method of gravimetric analysis(TG、DTG).
用热重分析法(TGA)探讨聚对苯二甲酸丁二醇酯(PBT)热降解的动力学,揭示了PBT的热稳定性、热解反应级数和热解活化能。
补充资料:聚对苯二甲酸乙二醇酯
    聚对苯二甲酸乙二醇酯是由对苯二甲酸二甲酯与乙二醇酯交换或以对苯二甲酸与乙二醇酯化先合成对苯二甲酸双羟乙酯,然后再进行缩聚反应制得。属结晶型饱和聚酯,平均分子量(2-3)×104,重均与数均分子量之比为1.5-1.8。相对密度1.368.熔点225℃,流动温度243℃:,玻璃化温度80℃,马丁耐热80 ℃,热变形温度98℃(1. 82MPa),分解温度353℃。具有优良的机械性能.刚性高.硬度大,吸水性很小,尺寸稳定性好。韧性好,耐冲击、耐摩擦、耐蠕变。耐化学性好,溶于甲酚、浓硫酸、硝基苯、三氯醋酸、氯苯酚,不溶于甲醇、乙醇、丙酮、烷烃。使用温度-100~120℃。
 弯曲强度  148-310MPa
 吸水性  0. 06%-0.129% 
 冲击强度  64.1-128J/m
 洛氏硬度  M 90-95
 伸长率  1.8%-2.7%  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条