1) structural steel 40Cr
40Cr结构钢
1.
Rotary bending fatigue tests for a structural steel 40Cr were performed in laboratory air,fresh water and 3.
选用40Cr结构钢,分别在空气、水和3。
2) 40Cr structural alloy steel
40Cr合金结构钢
1.
40Cr structural alloy steel is produced with EBT-LF-CC process in No.
莱钢特钢厂在1#连铸系统中采用EBT—LF—连铸工艺生产40Cr合金结构钢,通过合理控制用氧、调整炉渣碱度、采用Si—Ca线处理钢水、控制钢水过热度、调整拉速、合理控制二冷配水,确定了最佳工艺方案,提高了钢水收得率,解决了水口锈眼问题,保证了连铸生产顺行和质量稳定。
3) 40Cr steel
40Cr钢
1.
Residual stress release in quenched 40Cr steel under electropulsing;
脉冲电流作用下40Cr钢淬火残余应力的消除
2.
Superfining Process of 40Cr Steel;
40Cr钢晶粒超细化工艺研究
3.
Microstructure and mechanical properties of 40Cr steel nano-crystallized surface after high energy peening;
高能机械加工表面纳米化40Cr钢组织结构与力学性能
4) steel 40Cr
40Cr钢
1.
Study on measures to reduce stress of brazing Ti(C,N)based cermets to steel 40Cr;
Ti(C,N)基金属陶瓷/40Cr钢钎焊接头减应措施
2.
Effect of Horizontal Casting Process on Middle Crack ofΦ150 mm Tube Blank of Steel 40Cr
水平连铸工艺对40Cr钢Φ150 mm管坯中间裂纹的影响
3.
The welds seem to have similar strength to the basesteel 40Cr.
采用形变热处理加有机溶液保护膜的表面处理方法,可使40Cr—CrWMn钢在空气炉中实现超塑焊接焊接温度750—780℃,变形速率2×10~(-4)s~(-1)压力50—90MPa,时间3-5min,获得与基材40Cr钢一致的接头强度分析了焊接区的显微组织,并提出钢超朔焊接的微观机制为原子扩散和晶粒滑移造成的原始界面消
5) 40Cr steel
40Cr 钢
1.
Hard alloy YG-8 was used as surface coating materials for U70MnSi steel,and FW-1101 welding electrode for 40Cr steel.
采用硬质合金 YG-8和焊条 FW-1101作电极,在电火花表面强化器上强化了 U70MnSi钢和40Cr 钢的表面;用 X 射线衍射仪分析了强化层的结构,用滚动和滚、滑磨损试验研究了强化层的耐磨性,用阳极极化和浸泡试验研究了40Cr 钢表面强化后的耐腐蚀性能。
2.
——The effect of the stress and hydrogen on the fracture toughness behavior of 40Cr steel in 3.
本文利用悬臂梁试验机,测定了40Cr 钢的断裂韧性 K_(1c)和在3。
6) Cr steel
40Cr钢
1.
Hardness distributiog character during big area laser transformation hardening of 40Cr steel;
40Cr钢大面积激光相变硬化中的硬度分布特征
补充资料：[3-(aminosulfonyl)-4-chloro-N-(2.3-dihydro-2-methyl-1H-indol-1-yl)benzamide]
分子式：C16H16ClN3O3S
分子量：365.5
CAS号：26807-65-8
性质：暂无
制备方法：暂无
用途：用于轻、中度原发性高血压。
分子量：365.5
CAS号：26807-65-8
性质：暂无
制备方法：暂无
用途：用于轻、中度原发性高血压。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条