1) anti-corrosive design of steel box beam
钢箱梁防腐设计
3) stiff girder design
钢箱加劲梁设计
5) Design corrosion prevention
设计防腐
1.
Design corrosion prevention--selected corrosion resistant material or clad material at corrosion part;Construction corrosion prevention--strengthened the welding inspection and supervison;Process corrosion prevention--readjusted the chemical reagent quantity of "one removal three injection";Management corrotsion prevention--the whole stuff have a hand in cor.
金陵石化公司南京炼油厂 5 0 0 0kt/a常减压装置工艺设备的防腐分阶段进行了细化 :设计防腐———在易腐蚀部位选用耐腐蚀材料或复合材料 ;施工防腐———加强易腐蚀部位的焊缝监测和监督 ;工艺防腐———及时合理调整“一脱三注”化学药剂用量 ;管理防腐———全员参与防腐管理。
6) anticorrosive design
防腐设计
1.
The reasons of two kinds of typical corrosion are analyzed,and the deficiency in the anticorrosive design is indicated in this paper.
分析了MD-82型飞机2种典型腐蚀损伤产生的原因,指出了MD-82型飞机在防腐设计和制造中存在的缺陷。
2.
The bearing capacity of pier and bolt quantities required in pier foot were calculated,according to the pier characteristics,the proper anticorrosive design planning was proposed so as to decrease its influencing on the existing road traffic.
结合工程实例,介绍了高速公路钢箱混凝土门式墩的结构设计与施工,对墩柱承载能力及柱脚需要螺栓数量进行了计算,根据该桥墩的特点,提出了合理的防腐设计方案,从而减少对现有道路交通的影响。
补充资料：ANSYS壳单元分析箱梁
! Analysis a box beam section with shell elements of ANSYS
! 用ansys的壳体单元分析箱梁
! Box dimension: 10*4*4m with shell thickness of 0.04m
! By Lu Xinzheng, Depart. Civil Engineering, Tsinghua University, Beijing
! 陆新征，清华大学土木系
! Aug. 2004
! Define the Element
! 定义单元
/PREP7
!*
ET,1,SHELL93
!*
! Define the section for shells
! 定义壳单元截面
R,1,.04, , , , , ,
!*
! Define the material
! 定义材料
MPTEMP,,,,,,,,
MPTEMP,1,0
MPDATA,EX,1,,200e9
MPDATA,PRXY,1,,.3
! Setup the model
! 建模
! Define the keypoints
! 定义关键点
k,1,0,0,0
k,2,4,0,0
k,3,4,4,0
k,4,0,4,0
! Define the lines
! 定义线
l,1,2
l,2,3
l,3,4
l,4,1
! Define the section area
! 定义截面
a,1,2,3,4
! 用ansys的壳体单元分析箱梁
! Box dimension: 10*4*4m with shell thickness of 0.04m
! By Lu Xinzheng, Depart. Civil Engineering, Tsinghua University, Beijing
! 陆新征，清华大学土木系
! Aug. 2004
! Define the Element
! 定义单元
/PREP7
!*
ET,1,SHELL93
!*
! Define the section for shells
! 定义壳单元截面
R,1,.04, , , , , ,
!*
! Define the material
! 定义材料
MPTEMP,,,,,,,,
MPTEMP,1,0
MPDATA,EX,1,,200e9
MPDATA,PRXY,1,,.3
! Setup the model
! 建模
! Define the keypoints
! 定义关键点
k,1,0,0,0
k,2,4,0,0
k,3,4,4,0
k,4,0,4,0
! Define the lines
! 定义线
l,1,2
l,2,3
l,3,4
l,4,1
! Define the section area
! 定义截面
a,1,2,3,4
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条