1) 30CrMo gas cylinder steel
30CrMo气瓶钢
1.
Study on macro inclusions in 30CrMo gas cylinder steel
30CrMo气瓶钢中大型夹杂物的研究
2) CrMo steel bottle
30CrMo钢瓶
3) 30CrMo steel
30CrMo钢
1.
The spindle sleeve of 30CrMo steel belongs in heavy-walled part and in the past its mechanical properties were difficult to reach the requirement after being quenched and tempered.
30CrMo钢轴套属厚壁类零件,经调质处理后力学性能往往达不到要求。
2.
The anti-corrosion performance of 30CrMo steel covered with the graphite epoxy composite materials was evaluated in seawater through corrosion potential measurement,galvanic corrosion and neutral salt spray tests.
通过自腐蚀电位测量、电偶腐蚀试验、中性盐雾试验等方法,评价了海水环境中表面铺覆碳纤维环氧复合材料的30CrMo钢的腐蚀性能。
4) 30CrMo steel pump body
30CrMo钢泵体
1.
The crack morphology and forming reasons of 30CrMo steel pump body were observed and analyzed using optical microscopy, scanning electron microscopy, energy-dispersive X-ray analysis and chemical composition analysis.
利用光学显微镜、扫描电镜、能谱分析仪等对30CrMo钢泵体裂纹形貌和形成原因进行了观察和分析。
5) hydrogen cylinder
氢气钢瓶
1.
Referring to a case of explosion accident caused by erroneously refilling air into hydrogen cylinder, the main risk during releasing process of the cylinder containing hydrogen and oxygen mixture is analyzed.
针对一起空气误充入氢气钢瓶而导致使用时发生多起爆炸的事故,详细分析了氢氧混合气钢瓶在释放过程中的主要危险性,对释放过程中最可能存在的点火源即静电的产生机理及静电的放电条件进行了详细的论述,应用TNT当量法对可能发生的氢气钢瓶爆炸事故的破坏强度进行了估算。
6) cylinder steel
气瓶用钢
1.
Investigation has been made on variation of T[O] and non metallic inclusions in high pressure gas cylinder steel during production with BOF RH CC route.
对转炉— RH精炼—连铸工艺生产高压气瓶用钢 T[O]变化及非金属夹杂物进行研究的结果表明 ,在转炉出钢过程由于炉渣与脱氧产物作用生成的粗大球状夹杂物及铝脱氧生成的大尺寸 Al2 O3簇群状夹杂物绝大多数可由钢液排除 ,铸坯中存在的夹杂物主要是较小的块状和簇群状 Al2 O3及少量由于结晶器保护渣卷入造成的球状夹杂物。
补充资料：[3-(aminosulfonyl)-4-chloro-N-(2.3-dihydro-2-methyl-1H-indol-1-yl)benzamide]
分子式：C16H16ClN3O3S
分子量：365.5
CAS号：26807-65-8
性质：暂无
制备方法：暂无
用途：用于轻、中度原发性高血压。
分子量：365.5
CAS号：26807-65-8
性质：暂无
制备方法：暂无
用途：用于轻、中度原发性高血压。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条