说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 矩形工件
1)  rectangle workpiece
矩形工件
2)  toolbox rectangular part
工具箱矩形件
1.
In this paper,the drawing technology of the toolbox rectangular part was analyzed,the dimensions and shape of the blank were calculated,the drawing times and dimensions of the part were determined,the structure design of the blanking-drawing compound die for the part was introduced.
分析了工具箱矩形件的拉深工艺,计算了矩形件的毛坯形状及尺寸,确定了拉深次数及其工序尺寸,介绍了工具箱矩形件落料-拉深复合模结构设计。
3)  Rectangular box
矩形件
1.
Study of variable blank holder force curve for rectangular box drawing based on numerical simulation
基于数值模拟的矩形件成形变压边力曲线确定方法
2.
Most workpieces are non-axial symmetry complex shape such as rectangular box in engineering practice, so it has much academic value and significance to study deep drawing for a rectangular box.
在工程实践中,工件多是以矩形件为典型代表的非轴对称复杂形状。
4)  rectangular piece
矩形件
1.
The paper dealt with the optimal design problem of stock layout patterns of saw cutting blanking for rectangular pieces of a single size,proposed a kind of optimal layout method of rectangular pieces of a single size,pointed out the mathematical basis,selective conditions of the optimal solution and layout disposal of the particular solution.
讨论单一尺寸矩形件锯切下料排样方式的最优设计问题,提出一种单一尺寸矩形件优化排样方法,给出这一排样方法的数学依据、优化解的选择条件和特殊解的排样处理。
5)  rectangular pieces
矩形件
1.
The paper aims at solving the problems of incision of the rectangular pieces,such as the waste of the stuff and the energy sources,the low cutting efficiency and quality.
针对当前矩形件切割中板材和能源浪费、切割效率不高、切割质量不好等问题,从切割路径的优化入手,采用把相同尺寸的矩形件进行组合形成组合矩形块的思想进行优化排样;利用共边切割和连续切割,提出了一种适用的组合矩形块切割方式,并利用遗传算法解决了多选择、切割始终点不一致的组合矩形件切割顺序问题。
2.
Based on actual blanking technological of rectangular pieces,an application system of optimal layout of rectangular pieces and cutting simulation has been carried out,which is accomplished under the integrated environment of VC++6.
根据矩形件排样的实际下料工艺要求,采用Pro/ENGINEER的二次开发工具Pro/TOOL-KIT,在VC++6。
6)  rectangle box part
矩形盒件
1.
In this paper,expriments are done to study the effct of cylinder blankhold surface on rectangle box part drawing,and the effect law of between cyllinder surface and forming limits,strain distribution in deformation area are proposed.
本文实验研究了柱面压料面对矩形盒件拉深变形的影响,得到了柱面压料面形式对成形极限及毛坯变形区应变分布的影响规律。
补充资料:矩形

一.型态分析

  矩形是股价由一连串在二条水平的上下界线之间变动而成的型态。股价在其范围之内出现上落。价格上升到某水平时遇上阻力,掉头回落,但很快地便获得支持而升,可是回升到上次同一高点时再一次受阻,而挫落到上次低点时则再得到支持。这些短期高点和低点分别以直线连接起来,便可以绘出一条通道,这通道既非上倾,亦非下降,而是平行发展,这就是矩形型态。

[编辑]

二.市场含义

  矩形为冲突型,是描述实力相当的争战双方的竞争。

  这型态明显告诉我们,好淡双方的力量在该范围之间完全达致均衡状态,在这段期间谁占不了谁的便宜。看好的一方认为其价位是很理想的买入点,于是股价每回落到该水平即买入,形成了一条水平的需求线。与此同时,另一批看淡的投资者对股市没有信心,认为股价难以升越其水平,于是股价回升至该价位水平,便即沽售,形成一条平行的供给线。从另一个角度分析,矩形也可能是投资者因后市发展不明朗,投资态度变得迷惘和不知所措而造成。所以,当股价回升时,一批对后市缺乏信心的投资者退出;而当股价回落时,一批憧憬着未来前景的投资者加进,由于双方实力相若,于是股价就来回在这一段区域内波动。

  一般来说,矩形是整理形态,市道牛皮上落,顺升市和跌市中都可能出现,长而窄且成交量小的矩形在原始底部比较常出现。突破上下了限后有买入和卖出的讯号,涨跌幅度通常等于矩形本身宽度。

[编辑]

三.要点提示

  (1)矩形形成的过程中,除非有突发性的消息扰乱,其成交量应该是不断减少的。如果在型态形成期间,有不规则的高成交出现,型态可能失败。当股价突破矩形上限的水平时,必须有成交量激增的配合;但若跌破下限水平时,就不须高成交量的增加。

  (2)矩形呈现突破后,股价经常出现反抽,这种情形通常会在突破后的三天至三星期内出现。反抽将止于顶线水平之上,往下跌破后的假性回升,将受阻于底线水平之下。

  (3)一个高,低波幅较大的矩形,较一个狭窄而长的矩形型态更具威力。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条