说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 橡胶垫板支座
1)  rubber layer elastic supports
橡胶垫板支座
1.
Besides,the comparative dynamic characteristic analyzed for the roof structure using the rubber layer elastic supports and the fixed supports is performed.
结果表明:采用橡胶垫板支座的网壳结构杆件受力分布均匀,弦杆内力均位于屈服极限之内;张拉弦施工对屋顶变形的影响较大,而变温作用对屋盖变形影响不大。
2)  finite displacement supper support
有限位移橡胶垫板支座
1.
It put forward the idea for changing fixed support into finite displacement supper support based on site and analyses for structural intemal force.
分析重庆北碚朝阳吊桥在1992 年8 月高温时, 使固定支座破坏的原因, 在现场调查和结构内力分析基础上, 提出了将固定支座改为有限位移橡胶垫板支座方案, 实践证明是可行
3)  base isolation with rubber bearings
橡胶垫隔震支座
4)  rubber seat retainer
橡胶垫座
5)  elastomeric bearing pads
板式橡胶支座
1.
Combining the elastomeric bearing pads calculation example in section 8.
4节的板式橡胶支座的计算实例,参照ISO22762-2:2005规定的局部总应变校核方法,对橡胶支座在桥梁中的几种受力组合状态进行验算。
2.
The test method of mechanic properties, evaluat ion of results of elastomeric bearing pads have been made particularly.
交通部新修订的产品行业标准《公路桥梁板式橡胶支座》JT/T4-2004(代替JT/04-1993和JT3132。
6)  circular plate type elastomeric pad bearings
圆板式橡胶支座
1.
Through the compression tests of circular plate type elastomeric pad bearings and rigidity tests of the elastomer,the FEA model is founded according to the characteristic of the elastomer and primary theory of the elastomeric bearing behavior,and the stress of the plate type elastomeric pad bearings is also analyzed.
对圆板式橡胶支座做了抗压试验和橡胶硬度试验,在试验的基础上根据橡胶材料特性和橡胶支座行为特征基本理论,建立FEA模型,并对橡胶支座在轴心均布加载工况进行应力分析,结合支座抗压试验变形数据和支座内部应力分布规律证明该FEA模型基本正确,由计算结果可以看出在支座内部存在着应力分布不均匀的现象,同时还可看出圆板式橡胶支座圆周橡胶保护层具有减小支座内部剪应力的作用。
补充资料:橡胶模具、橡胶压模、橡胶硫化模
分子式:
CAS号:

性质:又称橡胶模具、橡胶压模、橡胶硫化模。用于压制橡胶产品的金属模型。一般用钢材(如45号钢)按图纸要求经机械加工而制得,并经热处理以提高其硬度及耐磨性。模具型腔与产品结构相同,型腔尺寸必须考虑不同橡胶的收缩率,在产品尺寸基础上进行放大或缩小,方可得到合适的产品尺寸。模具从工艺操作考虑还要设置流胶槽、启模口、定位销等。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条