1) pinhole camera model
针孔相机模型
1.
In this paper,light propagation path has been analyzed,and geometrical relation between center of actual rod in glass tube and edge of rod in image from a section has been analyzed by pinhole camera model,and line equation through actual rod center of the section has been derived with the edge of rod in image.
应用针孔相机模型,并考虑玻璃对光的折射现象,从光线的传播路径分析了一个断面上实际玻璃圆管中杆柱断面中心与照片边缘之间的几何关系,推导出由杆柱像的边缘得出通过实际杆柱断面中心的直线方程。
2) pinhole camera modeling
针孔摄像机模型
3) Pinhole camera
针孔相机
1.
Estimation of signal intensity for online measurement X-ray pinhole camera
实时测量的X射线针孔相机信号强度估算
2.
The X-ray imaging from the self emitting of the over-dense-plasma is obtained by pinhole cameras.
X射线成像诊断技术是在研究激光驱动的惯性约束聚变(ICF)过程中,利用针孔相机等设备对高温高密等离子体自身发射的X射线进行拍照,通过数值模拟还原内爆压缩,以此研究激光与等离子体相互作用、内爆动力学、激光X射线转换和辐射输运等物理过程。
5) pin-hole model
针孔模型
1.
Through building a pin-hole model for the projector and acquiring the related parameters including the model of the curved surface and the position of the observer, the pre-distorted images for the projector are obtained by transforming the desired images for the observer.
该方法将投影仪假设为针孔模型,并获取投影系统的相关几何参数,通过对观察者所需的理想图像进行变换获得投影仪所需预变形图像。
6) pin-camera
针孔照相机
补充资料:针孔
分子式:
CAS号:
性质:涂膜在干燥后,表面形成针状小孔,似皮革的毛孔状,这种缺陷称为针孔。在喷涂施工时,溶剂和空气很快气化并从湿涂膜中逸出,将形成小孔,因此时湿膜已缺乏足够的流动性,不能将小孔流平,留下了针状小孔。在漆中或溶剂中含有微量水时,更易产生针孔。严格选用稀释剂防止水分及其他杂物混入,同时控制施工黏度,可减轻或避免针孔的出现。
CAS号:
性质:涂膜在干燥后,表面形成针状小孔,似皮革的毛孔状,这种缺陷称为针孔。在喷涂施工时,溶剂和空气很快气化并从湿涂膜中逸出,将形成小孔,因此时湿膜已缺乏足够的流动性,不能将小孔流平,留下了针状小孔。在漆中或溶剂中含有微量水时,更易产生针孔。严格选用稀释剂防止水分及其他杂物混入,同时控制施工黏度,可减轻或避免针孔的出现。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条