1) PET/ITO films
PET/ITO薄膜
2) ITO films
ITO薄膜
1.
Transparent conductive ITO films (5 wt%~20wt% Sn-doped) were fabricated on soda lime float glass substrate by a colloid technique.
以金属铟和锡盐为原料采用胶体法制备Sn掺杂三氧化二铟(ITO)前驱物浆料,通过提拉法在镀有SiO2薄层的浮法玻璃基片上制备透明导电ITO薄膜。
2.
High quality ITO films were deposited on glass substrates by sol-gel method in the solution composed of indium metal(In) and stannic chloride (SnCl 4·5H 2O).
以In金属和SnCl4·5H2 O作为原材料 ,采用溶胶一凝胶法在玻璃基体上制备了高质量的ITO薄膜 ,并分析了Sn掺杂时、热处理温度、热处理时间三种工艺参数对ITO薄膜电学性能的影响 ,确定了ITO薄膜的相组
3.
Zirconium-doped ITO films were deposited on glass substrate by co-sputtering technology with two targets.
利用双靶共溅法在玻璃衬底上沉积了Zr掺杂ITO薄膜,对比研究了在不同氧流量下ITO和ITO∶Zr薄膜性能的变化。
3) ITO film
ITO薄膜
1.
Influence of nitrification methods upon optical and electrical properties of ITO films;
氮化处理对ITO薄膜光电特性影响
2.
Experimental studies on thermal shielding and saving energy of the coated ITO film for automobile front windshield;
汽车前挡风玻璃用ITO薄膜的隔热及节能实验研究
3.
The experimental results showed that it is absolutely feasible to fabricate ITO film on the quartz matrix by sol-gel techni.
ITO薄膜具有由多个粒子堆积而成的多孔微观结构,其晶体结构为立方锰铁矿结构,[111]为明显的择优取向,经过5次镀膜后其厚度在150nm以下,薄膜的方电阻为110Ω,其电阻率约为1。
4) ITO thin films
ITO薄膜
1.
Progress in preparation of ITO thin films by Sol-Gel process;
溶胶-凝胶法制备ITO薄膜研究进展
2.
The XRD, SEM and EDS are used to characterize the ITO thin films.
以铟锡氯化物为原料,采用水热法在玻璃基片上制备了氧化铟锡(ITO)薄膜,并利用X射线衍射 (XRD)、能谱分析(EDS)、扫描电子显微镜(SEM)等手段对薄膜的相结构、化学组成及形貌进行了表征,研究了水热温度和时间等条件对ITO薄膜光吸收特性的影响。
3.
The phase composition and morphology properties of ITO thin films were characterized by the techniques of X-ray diffraction(XRD)and scanning electron microscope(SEM).
结果表明,采用溶胶-凝胶旋涂法制备的ITO薄膜是由立方相纳米颗粒构成,随涂层增加,薄膜表面变得平滑。
5) ITO thin film
ITO薄膜
1.
The article pointsed out the manufacturing way of Indium-methyl-ethyl-diketone which was important raw material of ITO thin film.
介绍了ITO薄膜重要原料乙酰丙酮铟的制备方法,乙酰丙酮铟一次合成产率99·8%,产品纯度99·95%。
2.
The article points out way manufacturing Indium-methyl-ethyl-diketone which is important raw material of ITO thin film,the controlled condition is as that:organic multi-acid density 8.
介绍ITO薄膜重要原料乙酰丙酮铟的制备方法,制备条件:有机多元酸浓度8。
3.
Several methods of the preparation of ITO thin film with sol-gel technique were introduced.
介绍了几种用溶胶 凝胶法制备ITO薄膜的工艺方法 ,用其中一种无机的方法成功制备了ITO透明导电膜。
6) ITO conductive films
ITO电薄膜
补充资料：PET
聚对苯二甲酸乙二醇酯是由对苯二甲酸二甲酯与乙二醇酯交换或以对苯二甲酸与乙二醇酯化先合成对苯二甲酸双羟乙酯，然后再进行缩聚反应制得。属结晶型饱和聚酯，平均分子量(2-3)×104，重均与数均分子量之比为1.5-1．8。相对密度1.368．熔点225℃，流动温度243℃：，玻璃化温度80℃，马丁耐热80 ℃，热变形温度98℃(1. 82MPa)，分解温度353℃。具有优良的机械性能．刚性高．硬度大，吸水性很小，尺寸稳定性好。韧性好，耐冲击、耐摩擦、耐蠕变。耐化学性好，溶于甲酚、浓硫酸、硝基苯、三氯醋酸、氯苯酚，不溶于甲醇、乙醇、丙酮、烷烃。使用温度-100～120℃。
弯曲强度 148-310MPa
吸水性 0. 06％-0.129％
冲击强度 64.1-128J／m
洛氏硬度 M 90-95
伸长率 1.8％-2.7％
弯曲强度 148-310MPa
吸水性 0. 06％-0.129％
冲击强度 64.1-128J／m
洛氏硬度 M 90-95
伸长率 1.8％-2.7％
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条