|
|
|
说明：双击或选中下面任意单词，将显示该词的音标、读音、翻译等；选中中文或多个词，将显示翻译。
|
|
|
您的位置： 首页 -> 词典 -> 渐开线环形齿球齿轮
1) the involute ring tooth spherical gear
渐开线环形齿球齿轮
1.
Then,the characteristics of the working flanks of the involute ring tooth spherical gear are analyzed and the equations to calculate the master curvature radius are derived.
为研究渐开线环形齿球齿轮传动过程中齿轮副间的接触力,基于Hertz弹性接触理论定义了齿面接触点的刚度系数;利用微分几何相关知识,分析了球齿轮的齿面特征,得到了实时啮合点主曲率半径计算公式;研究了重合度系数对啮合刚度的影响,结合球齿轮机构传动特点,推导出任意位置反向啮合点位置计算公式;最后通过一个实例说明球齿轮机构接触点刚度系数具有典型的时变特征。
2) Conical involute gear
渐开线锥形齿轮
1.
The gear hobbing of conical involute gear is a complex generating motion with doubledegree of freedom.
根据齿轮啮合原理中多自由度齿面包络理论,对渐开线锥形齿轮在滚齿加工中,刀具与工件的相对运动及产形齿条的形成机理进行了深入分析,证明了产形齿条的存在,并求解了其齿面形状。
3) conical involute gear
锥形渐开线齿轮
4) involute toothed sprocket
渐开线齿形链轮
1.
In this paper,calculated impact velocity of odontoid chain meshed as well as analyzed meshing parameters about the odontoid chain and the involute toothed sprocket,transmission become more stable through improving chain drive′s performance,and then laid the foundation for meshing design and motion analysis of the odontoid chain and the involute toothed sprocket.
作者对齿形链啮合过程的冲击速度进行了分析计算,并对齿形链和渐开线齿形链轮的啮合参数进行了研究,以期改善其链传动性能,使传动更加平稳,并为齿形链与渐开线齿形链轮的啮合设计和运动分析提供理论依据。
5) space involute post-tooth ring-sphere gear
空间渐开线柱齿环球面齿轮
1.
A new transmission mechanism for space track(space involute post-tooth ring-sphere gear mechanism) is developed,the parameter equation of the profile and the minimum turn radius formula in the horizontal direction are calculated out.
介绍了一种新研制出的能够实现空间运动轨迹的传动机构———空间渐开线柱齿环球面齿轮机构,推导了此种齿轮齿廓的参数方程和此种传动机构在楼梯轨道水平方向上运动的最小转弯半径计算公式。
6) involute gear
渐开线齿轮
1.
Confirmation of the measuring teeth number of involute gear common normal;
渐开线齿轮公法线跨测齿数的确定
2.
Accurate modeling of Involute gear machined by the principle of generation of curve;
基于曲线的生成原理实现渐开线齿轮的实体建模
3.
Exactitude Modeling of Involute Gear on Pro/E;
基于Pro/E的渐开线齿轮精确建模
补充资料：齿轮轮齿渐开线、螺栓、弹簧autolsp源程序
一、齿轮轮齿渐开渐开线 (defun c:gear(/)
(
setq
p0 (getpoint"输入齿轮中心p0: ")
m (getreal"输入齿轮模数M: ")
z (getint"输入齿轮齿数Z: ")
ha 1
c 0.25
a (/ pi 9)
ra(/ (* (+ z (+ ha ha)) m) 2)
rf(/ (* (- z (+ (+ ha ha) c)) m) 2)
r(/ ( * m z) 2)
rb ( * r (cos a))
ri rb
ang 0
g (polar p0 ang rb)
)
(command "circle" p0 ra)
(command "circle" p0 rf)
(command "circle" p0 r)
(command "line" g)
(while (< ri ra)
(setq
ang ( + ang(/ pi 360))
ri ( / rb (cos ang))
cta ( - (/ (sin ang) (cos ang)) ang)
g(polar p0 cta ri)
) (command g)
)
(command )
)
二、螺旋源程序
(defun errMsg (s)
(if (/= s "function cancelled") (princ (strcat "\nError: " s)))
; 当命令执行时出现错误
(setvar "cmdecho" ocmdold) ; 例如用户按下了CTRL + C
(setvar "osmode" osmold)
(setq *error* olderr) ; 恢复旧的错误处理
(princ)
) (defun c:3Dthread (/ radouter threadpitch threadlength threadangle
ptStart innerdiafactor radmid radinner ocmdold osmold 4H 5H 6H h6 g6)
;-------------------------------------------------------------------
; 获取公制外径大小、螺距总长
; 然后计算一系列几何点
; 并且关闭对象捕捉、命令回显
;-------------------------------------------------------------------
(setq 4H (list 0.0015 0.002 0.002 0.0025 0.003 0.0035 0.004 0.005 0.006 0.007 0.008 0.009 0.010))
(setq 5H (list 0.002 0.0025 0.003 0.004 0.0045 0.0055 0.0065 0.0075 0.009 0.010 0.0115 0.0125 0.0135))
(setq 6H (list 0.003 0.004 0.0045 0.0055 0.0065 0.008 0.0095 0.011 0.0125 0.0145 0.016 0.018 0.020))
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|