1) plastic load index
塑性荷载指数
1.
On the basis of the YAI(yield approach index) and PLI(plastic load index),the new concept,FAI,is introduced.
结合屈服接近度(YAI)和塑性荷载指数(PLI)的概念,提出了破坏接近度(FAI)的新定义。
2) plastic load
塑性载荷
1.
By considering the contact between the teeth and utilizing the face to face contact model with contact element and coulomb friction model,a computing method for plastic load of tooth-locked quick actuating pressure vessel based on finite element stress analysis and the 5% maximum principal strain rule have been developed.
通过接触单元数值模拟啮合齿的接触过程,采用5%最大主应变准则,建立了基于整体有限元分析的齿啮式快开压力容器塑性载荷计算方法。
2.
By considering the contact between the teeth and utilizing the face to face contact model with contact element and coulomb friction model,the author have developed a computing method for plastic load of tooth-locked quick actuating pressure vessel based on finite element stress analysis and stress categorization.
通过接触单元来数值模拟啮合齿的接触过程,建立了基于整体有限元分析的齿啮式快开压力容器塑性载荷计算方法。
3.
The proposed criterion is used to evaluate plastic loads in pressure vessel design by analysis using elastic-plastic finite element analysis to guard gross plastic deformation of pressure vessel.
提出了按5%应变确定塑性载荷的最大主应变准则。
3) point load index number
点荷载指数
4) plasticity index
塑性指数
1.
Effect of plasticity index of saturated soft clay on its deformation parameters;
饱和软粘土的塑性指数对其压缩变形参数的影响
2.
The article carries out the study and discussion only from improv- ing the soil plasticity index.
该文仅从改善土的塑性指数提高灰土抗裂性能进行研究与探讨,通过试验和应用已见成效。
5) plastic index
塑性指数
1.
On the expression of plastic index and the analysis of contact characteristics of rough surfaces considering the surface film and thermal effect;
考虑表面膜及热效应时粗糙表面的塑性指数和接触性能
2.
According to systemic test of powdered fly ash's pl astic and liquid limits of different proportion and different mixing time, the s tudy show that the plastic index decrease as the increase of powdered fly ash co ntent and prolong of the mixing time.
对不同配比、不同混合时间的粉煤灰土的塑液限进行了系统测定,结果表明,随粉煤灰含量的增加,土的塑性指数减小;随时间的延长,土的塑液限减小;详细分析了粉煤灰对粘土的塑液限影响的机理。
3.
The plastic index ψ were calculated in different contacts.
在此基础上计算了不同接触情况下的塑性指数ψ,其范围在4～15之间,所以渗硫面接触主要为塑性接触。
6) plastic limit load
塑性极限载荷
1.
Analysis on the plastic limit load of gas pipe elbows with pitting corrosion;
含点蚀缺陷燃气管道弯管的塑性极限载荷分析
2.
Analysis of plastic limit loads of tee with bottom wall-thinning under pressure and moment;
压弯载荷下底部减薄三通塑性极限载荷分析
3.
Research on Plastic Limit Load of Local Thinning Elbow for Engineering Calculation Method;
含局部减薄弯管塑性极限载荷工程计算方法研究
补充资料：塑性
分子式：
CAS号：
性质：又称塑性。材料受外力、热等作用变形后，能完全或部分保持其变形的性质。是材料的一种加工和使用性能。橡胶的可塑性通常用外力消除后仍保留的残余变形来表示，它是评价橡胶加工性能的重要指标。在橡胶加工过程中，由于橡胶具有弹性会给其加工过程带来困难，适当提高橡胶的可塑性有利于橡胶的加工操作。但可塑性过大，又会使橡胶制成品的物理机械性能下降，对加工操作也不利。通常在满足工艺加工要求的前提下，以具有最小可塑度为宜。
CAS号：
性质：又称塑性。材料受外力、热等作用变形后，能完全或部分保持其变形的性质。是材料的一种加工和使用性能。橡胶的可塑性通常用外力消除后仍保留的残余变形来表示，它是评价橡胶加工性能的重要指标。在橡胶加工过程中，由于橡胶具有弹性会给其加工过程带来困难，适当提高橡胶的可塑性有利于橡胶的加工操作。但可塑性过大，又会使橡胶制成品的物理机械性能下降，对加工操作也不利。通常在满足工艺加工要求的前提下，以具有最小可塑度为宜。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条