说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 压下位置系统
1)  pressing down position system
压下位置系统
1.
A robust dynamic output feedback synchronous controller is designed for the pressing down position system with uncertain parameters and outside load disturbance.
冷带轧机操作侧和传动侧位置子系统的内部参数和外界负载不一致,并且均存在一定的不确定性,这会造成两侧压下位置系统动静态性能不同和压下位置的不同步,从而影响被轧带材两侧的厚度和板形质量。
2)  reduction position
压下位置
1.
2 Steelmaking Plant of WlSCO,the main technological parameters were analyzed and optimized, such as reduction position,reduction amount,and reduction ratio.
结合武钢二炼钢动态轻压下技术的应用情况,对压下位置、压下量、压下率等主要参数进行了分析及优化。
3)  hydraulic position servo system
液压位置系统
4)  light screw down position
轻压下位置
1.
COMSOL software is used to simulate the solidification process of the square billet continuous casting,and factors which influence the position of the solidification point have been analyzed,which provides a effective means for determining the dynamic light screw down position of the casting blank.
本文采用COMSOL软件模拟方坯连铸的凝固过程,分析了影响凝固点位置的因素,为确定铸坯的动态轻压下位置提供了一种有效的手段。
5)  rolling down system
压下系统
1.
Balancing system provide proper rolling force with rolling down system.
介绍了由压下、弯辊和平衡缸3个分系统组成的HGC系统的原理及实现方法,其中,压下系统由2个伺服阀分别控制2个压下缸实现轧钢;弯辊系统由32个液压缸组成,实现钢板板型控制;平衡缸系统配合压下系统提供合适的轧制力。
6)  Position system
位置系统
1.
Research on Control Methods of Position System of Examination Platform of Anti-rolling Tank;
水舱试验摇摆台位置系统控制方法研究
2.
A mathematical model is built for the hydrostatic drive position system with secondary regulation in accordance with its actual operatine conditions and it is simplified as appropriate into a third order model.
建立了二次调节静液传动位置系统的数学模型,并在允许的情况下将其简化为三阶系统。
3.
A digital controller based on DSP is designed for position system of the test bed of ship,which is used for testing the anti-rolling tank.
本文针对研究减摇水舱性能的船舶试验台位置系统,设计了基于DSP芯片的数字控制器。
补充资料:冲击波超压与动压

[解释]:  核爆炸产生的高温、高压火球膨胀,在周围介质中形成连续向外传播的压力脉冲(或冲击波),冲击波阵面传播到空间某点时,超过周围环境大器的压力称超压;空气粒子高速随波阵面运动产生的冲击压力称动压。超压和动压都以帕斯卡(Pa)为主单位。超压随时间的变化取决于爆炸威力、距爆点的距离和爆心周围的介质情况。特定地点的峰值超压一般出现在冲击波阵面到达该点的瞬间,超压在该点的持续时间称为正压作用时间。尔后,该点的压力下降到低于周围压力,称为负压,再逐渐回升到周围压力值。对人员的直接冲击伤,超压为20—29千帕可引器轻度伤;29—59千帕可导致中度伤;59—98千帕可造成重度伤;大于98千帕可造成极重度伤。动压为10—20千帕可造成中度伤;20—39千帕可造成重度伤;大于39千帕可造成极重度伤。动压的推动、抛掷和超压的挤压会造成物体变形和毁坏。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条