说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 收敛K-半径
1)  convergence K-radius
收敛K-半径
2)  Convergence radius
收敛半径
1.
Elucidation about convergence radius of the sum of two power series;
关于2个幂级数和的收敛半径的说明
2.
On the Probing of the Solution Convergence Radius of Power Series;
幂级数sum from n=0 to ∞(a_nx~(φ(n)))收敛半径的两种求法
3.
By the way,convergence radius of power series is given.
对于正项级数中的∑n∞=1bann给出了一种新的审敛法,推广了文[1]中的判别方法,并且用它解决了极限值为Eu ler常数的数列极限存在问题,以及求幂级数的收敛半径。
3)  radius of convergence
收敛半径
1.
This paper through discusses the clerical error of the professor Zhao on the radius of convergence of the power series A short-cut method for finding the radius of convergence about the sum from n=0 to ∞ a_n(bx+c)~(np+q) type′s power series.
本文通过对赵树嫄教授主编的《微积分》关于求幂级数收敛半径一处笔误的讨论,得出关于sum from n=0 to ∞ a_n(bx+c)~(np+q)型幂级数收敛半径的简捷求法。
2.
For series like ∑∞n=0anxkn+b(k∈N,b∈Z),it is usual to find the interval and radius of convergence by the d Alembert determination method,not to do those by the formula of ρ=limn→∞an+1an,when the series lacks terms.
对形如∑∞n=0anxkn+b(k∈,b∈)的幂级数,当其缺项的时候,不能直接用公式ρ=li mn→∞an+1an求其收敛半径与收敛区间(本文约定收敛区间不含端点),一般都是直接采用达朗贝尔(比值)判别法求其收敛半径与收敛区间。
3.
To find the solution of power series convergence domain,it is important to get its radius of convergence.
求幂级数收敛域最关键的是求它的收敛半径。
4)  associated convergence radius
相伴收敛半径
5)  Painleve-Kuratowski convergence
P-K收敛
1.
This paper investigates the stability of the sets of efficient points of vectorvalued and set-valued optimization problems when the control cone is regular but need not have a bounded base in the sense of Painleve-Kuratowski convergence of set sequence.
利用集合序列的P-K收敛的概念,在控制锥是正则锥但未必具有有界基的情况下,讨论了向量值优化和集值优化问题的有效点的稳定性,改进了[2]中相应的结论。
6)  K-M convergence
K-M收敛
补充资料:利用小半径模具弯制大半径管件
高档汽车座椅因座椅形状需要,其骨架通常有3维大半径复合圆弧,作为生产汽车座椅的专业厂,我们常有这样的零件要加工。
  安徽淝河客车厂凯斯鲍尔豪华客车座椅靠背骨架,成型圆弧较大,有4种弯曲半径,且有3维复合弯,我们手头有的精密弯管设备-美国伊顿伦纳德公司的矢量弯管机VB200HP只能弯制弯曲半径203.2mm以内的管件。
  如何利用弯管机弯出这样的大半径3维复合弯?我们分析了零件的特性:形状要正确,但由于骨架是包裹在护面和海绵软垫之中的,零件不外露。因此采取了将大半径圆弧分解为多个小半径圆弧与多段直线依次相连的方法,近似地获得所需形状。首先将其分段,将各大圆弧作成多段55mm长的直线相连的折线,计算出各交点坐标,然后用恰当半径的圆弧结合旋转度将相邻线段连接,形成近似的大半径圆弧。这样产生的新的管件符合VB200HP弯管机的加工条件,同时由于有较多点的坐标与原设计一致,分段弯曲造成的过渡不流畅由于零件的装配隐蔽性而显得无关紧要。
  实践中,我们在对管件实样分段划线的基础上采用美国伊顿伦纳德公司的另一台设备-VECTOR 1 S4XL激光测量机,通过对每一分段测2点的方法,获取圆弧近似折线的交点坐标,进而转换成弯管程序弯制管件。表1为该零件的坐标,表2为该零件的弯管程序(注:L为直线段长度,R为旋转度,A为弯曲角度)。
  进而,我们可以把这种方法应用到其他类似方面-只要是隐蔽的或者是非装饰性的还有试制的弯管,都可以采用本文所述方法。这样,许多原来不能用VB200HP弯管机弯制或难以弯制的管件,现在都能轻而易举地制造出来了。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条