说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 拱支座
1)  arch support saddle
拱支座
1.
Steel roof arch support saddle in Parking and Traffic Center Project of Capital Airport Expansion Engineering is in a three dimensional structure, there are a great many of arch support saddles that high and tilt, those arch support saddles is required to reaching A grade as-cast-finish concrete; the embedded parts on the top are so heavy (1.
北京首都机场扩建工程停车楼及交通中心(GTC)工程屋顶钢结构拱支座为三向曲面空间三维结构,拱支座数量多、高度较高且为倾斜结构,并要求清水混凝土达到A类;拱支座顶部预埋件重量大(1。
2)  two support blocks arch truss with drawbars
双支座拱桁架
3)  four support blocks arch truss with drawbars
四支座拱桁架
1.
Moreover, the steel dosage of four support blocks arch truss with drawbars reduces by 6%, while the reinforcement ratio of the columns in the bent reduces by 25%.
本文通过工程实例,分析带拉杆拱桁架选用的原因,并在普通两支座拱桁架的基础上,创造性地采用了四支座拱桁架,两者的用钢量均不足常规设计用钢量的1/3四支座带拉杆拱桁架用钢量又比两支座带拉杆拱桁架减少6%,排架柱的配筋减少25%。
4)  flat roundup abutment board
扁拱梁支座板
5)  arch seat
拱座
1.
The static and dynamic load tests were made for structural performance of the strengthened arch seat of a flying bird type arch bridge.
针对某飞鸟式拱桥拱座加固后结构性能进行静动载试验。
2.
The deformation of arch springs of hingeless arch has significant influence on the internal forces of arch bridge and the selection of proper arch seats to be built on the thick overburden layer ground is thus extremely important to reduce the deformation of the arch springs.
无铰拱的拱脚变位对拱桥内力影响显著,在厚覆盖层地基上选择合适的拱座形式以减小拱脚变位十分重要。
3.
Several years after a fly-bird type self-balanced tied arch bridge was open to traffic, the vertical cracks normal to the axial of the bridge, almost running through the whole arch seats occurred in west arch seats of the main bridge of the arch bridge, and also the propagation of the cracks does not tend to be stable.
某飞鸟式自平衡体系系杆拱桥在建成通车几年后,主桥西侧拱座出现了垂直于桥轴线、基本贯通整个拱座的竖向裂缝,且裂缝发展未趋稳定。
6)  arch abutment
拱座
1.
Using MatLab software for deducing safety factor of point shearing resistance on the arch abutment space;
利用MatLab软件推导拱座空间点抗剪安全系数
2.
Through the combined modeling method with Surfer and Rhinoceros,such the control factors as the topography,structural face,block,water thrust and seepage pressure are unfolded and analyzed by three-dimensional model,which could only be unfolded by two-dimensional model in stability analysis of the arch abutment with the rigid limif equilibrium method in the past.
采用Surfer和Rhinoceros联合建模法,将以往采用刚体极限平衡法分析拱座稳定时只能以二维展现并分析的地形、结构面、块体、水推力、渗压等控制性要素以三维模型展现,将平面模型转换为实体模型,实现了三维可视化操作。
补充资料:双曲拱坝
      双向(水平向及竖向)弯曲的拱坝。它是拱坝中最具有代表性的坝型。双曲拱坝的水平向弯曲可以发挥拱的作用,竖直向弯曲可实现变中心、变半径以调整拱坝上下部的曲率和半径。双曲拱坝的优越性可从这两个方向的弯曲中体现出来。一般情况,上部半径大些,可使拱座推力更指向岸里;下部半径小些,可适当加大下部中心角以提高拱的作用。因此,双曲拱坝一般均采用变中心、变半径布置,具体又有等中心角及变中心角之分和拱冠梁有近乎直立和俯向下游之分(见拱坝)。为适应特定的地形、地质和溢洪、泄水及厂房布置要求,使拱坝体型、应力及拱座稳定等更趋合理,可调整双曲拱坝的各种参数,并可在坝基增设垫座以周边缝与坝身分开,或在坝身设置切入缝和分离缝等(见图)。设置周边缝和垫座一般可改善地基(特别是不均匀或不规整地基)对拱坝坝身应力的影响,及改善或降低坝基(即垫座底部)应力以适应地基的要求。设置切入缝或分离缝可改变拱梁系统荷载分配以改善坝身及坝基应力以适应特定的要求。周边缝、切入缝及分离缝自20世纪50年代以后才逐渐出现。它们改进了拱坝应力并扩大了拱坝的应用范围,优点较多。但也有人认为这些缝破坏了拱坝的整体性,削弱了坝体强度,其结构作用不明确。虽然对它们的作用至今还存在肯定和怀疑两种不同的观点,但从世界修建拱坝的实践看,这些结构缝屡见不鲜,且有逐渐增多的趋势。
  
  
  20世纪50年代前后,意大利、瑞士、法国建成了较高的有代表性的双曲拱坝。当时最高的意大利瓦依昂拱坝,高262m,最大底厚22.1m,厚高比仅0.084;瑞士莫瓦桑拱坝高237m,最大底厚53.6m,厚高比为0.227。这些双曲拱坝的建成,标志着拱坝的设计施工达到了一个新的水平。意大利著名工程师C.塞门扎等称:双曲拱坝体形的决定在很大程度上依靠模型试验。50~60年代许多著名的双曲拱坝的体型设计都是出自世界上著名的意大利模型和结构试验研究所。当前电子计算技术的发展,拱坝体型优化已能通过计算解决。过去有人认为双曲拱坝对溢洪及泄水不利,但通过许多工程的实践,这个问题已逐渐趋于解决。如利用双曲拱坝稍向下游俯悬,可以使坝顶溢流及坝身泄水孔射流抛离坝脚。中国正在施工的二滩拱坝高240m,设计使坝顶溢流水舌与坝身中泄水孔水舌在空中相撞并在坝趾下游修建消能塘,总溢流及泄流量高达13000m3/s,消能效果较好。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条