1) single carbon drawing
一次拉碳
1.
The present article analyses the main factors impacting the productivity of the converter and describes the production practice of raising the potential productivity of the converter by taking a series optimized processing measures such as increasing the converter charge,intensifying the oxygen blow rate and adopting the single carbon drawing practice.
分析影响转炉产能的主要因素,阐述武钢第一炼钢厂通过增加转炉装入量、提高转炉供氧强度、采用一次拉碳等工艺优化措施,来充分挖掘转炉产能的生产实践。
3) one-go
一次拉成
1.
During the smelting process for V-Ti containing molten iron,we can increase the convertor life by improve the walling up technology,using the one-go operation,decreasing the tapping temperature,restructurding the slag system and improving the effectivensee of slag-splashing for protecting of converter and so on.
介绍了承钢采用双联工艺,在用含钒钛铁水炼钢生产过程中通过改进砌炉工艺,执行一次拉成出钢操作,降低出钢温度,改造渣系,提高溅渣护炉效果等措施的实施大幅度提高转炉炉龄,为不同生产条件下提高炼钢炉龄提供了借鉴。
6) primary carbide
一次碳化物
1.
The results showed that adding Cr powder and graphite to Ni-based alloy powder can yield primary carbide precipitate in the surfacing layer,which obviously increases its hardness.
结果表明,在镍基合金粉中加入铬粉和石墨,堆焊层中析出了一次碳化物,可显著提高堆焊层的宏观硬度;随铬粉和石墨加入量的增加,堆焊层中一次碳化物的析出量随之增加,堆焊层的宏观硬度相应提高,最高可达62HRC,是镍基合金粉光束堆焊层的2。
2.
The results show that adding Cr powder and graphite to Ni-based alloy powder can make primary carbide precipitate in surfacing layer, which observably increase the hardness of surfacing layer.
研究结果表明,在镍基合金粉中加入铬粉和石墨,堆焊层中析出了一次碳化物,可显著提高堆焊层的宏观硬度;随铬粉和石墨加入量的增加,堆焊层中一次碳化物的析出量随之增加,堆焊层的宏观硬度相应提高,最高可达HRC62,是镍基合金粉光束堆焊层的2。
补充资料：碳化硅晶须补强碳化硅陶瓷基复合材料
分子式：
CAS号：
性质：以碳化硅陶瓷为基和以碳化硅晶须为增强剂的新型陶瓷材料。通过晶须的载荷转移、拔出及裂纹偏转作用，获得比普通碳化硅更高的强度和韧性。使用温度达1400℃。是一种重要的高温结构陶瓷。用于燃气轮机叶片等高温部件和耐磨件制造。采用原位生长工艺和烧结工艺制取。
CAS号：
性质：以碳化硅陶瓷为基和以碳化硅晶须为增强剂的新型陶瓷材料。通过晶须的载荷转移、拔出及裂纹偏转作用，获得比普通碳化硅更高的强度和韧性。使用温度达1400℃。是一种重要的高温结构陶瓷。用于燃气轮机叶片等高温部件和耐磨件制造。采用原位生长工艺和烧结工艺制取。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条