1) cold lateral condensation
冷侧方加压
1.
And then they were randomly divided into three groups:1 Modified by step-back technique,cold lateral condensation;2 Modified by step-back technique,warm vertical condensation;3 control group,no modification and condensation.
结论冷侧方加压充填后牙齿的抗力强于热垂直加压。
2) cold lateral condensation of gutta-percha
冷牙胶侧方加压法
1.
Objective:To compare the root filling results of 2 thermoplasticized gutta-percha filling techniques(Ultrafil 3D and ObturaⅡ) with cold lateral condensation of gutta-percha.
目的:比较2种热塑牙胶充填技术(Ultrafil 3D和ObturaⅡ)与冷牙胶侧方加压法充填根管的效果。
2.
AIM:To compare the apical sealing ability of continuous-wave technique with cold lateral condensation of gutta-percha.
微渗漏和微缝隙在连续波热塑充填和冷牙胶侧方加压法充填之间存在显著性差异(P<0。
3) cold gutta-percha lateral condensation
冷牙胶侧方加压充填法
4) Lateral Condensation
侧方加压
1.
Analysis of the Effect on the Stress of Root Canal Wall by Vertical and Lateral Condensation Procedures;
垂直加压充填和侧方加压充填对根管壁应力影响的分析
5) spreader
[英]['spredə] [美]['sprɛdɚ]
侧方加压器
1.
Comparison of NiTi and stainless-steel spreaders penetration in curved canals;
两种侧方加压器进入弯曲根管深度的实验研究
2.
Objective To compare the initial penetration depth of nickel-titanium(NiTi) and stainless-steel(SS)spreader during lateral compaction and the quality of the seal in curved canals.
目的比较镍钛(NiTi)侧方加压器和不锈钢(SS)侧方加压器进入不同程度弯曲根管的深度和根充质量。
3.
The finger spreaders are the instruments which can be used to condense the gutta-percha points.
冷牙胶侧方加压充填技术是目前应用最为普遍的一种根管充填技术,而侧方加压器(spreader,以下简称侧压器)则是该充填技术中必不可少的器械。
6) cold lateral condensation technique
冷牙胶侧方加压充填技术
1.
METHODS: In vitro study,the sealing ability of Thermafil obturators technique (TC) or cold lateral condensation technique (LC)assesssd by microleakage using 40 mandibular premolars with straight or lightly curved canals.
方法 :4 0个离体单根管前磨牙 (根管弯曲度为 0°～ 10°)随机分为两组 ,分别采用Thermafil根管充填技术 (TC)和冷牙胶侧方加压充填技术 (LC)进行根管充填。
补充资料：冷胶活化法
冷胶活化法 现代家具工艺技术之一。是一种聚腊酸乙烯封边的方法。在封边条入机床前，用热空气和高频加热活化，使水分排出，树脂部分加强。然后，只要很短的加压时间就能象接触胶那样粘住。用此法封边时，基材加工和封边后侧边加工都比热熔胶封边时精度高。其胶缝不明显，几乎看不见。因此便于工件铣削和研磨。另外，在成型封边时，边部呈弧形，与平面间没有清晰的界线，形成一条余缝，因此可以不用整块的木材作镶边条。其优点有：１、费用节约；２、转角部位不用垫入木块；３、在酸腐蚀或老化时不变色。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条