1.
Effects of Pouring Temperature on the Solidification Microstructure of Single Crystal Superalloy DD6
浇注温度对DD6单晶高温合金凝固组织的影响
2.
How much pouring temperature of EPC should be improved than that of sand mould casting
消失模铸造的浇注温度应比砂型铸造提高多少
3.
Influence of Pouring Temperature and Injection Speed on Microstructure and Hardness of Al-10%Si Alloy
压射速度和浇注温度对Al-10%Si合金组织与硬度的影响
4.
Influence of Pouring Temperature on Primary Austenite in Semi-solid Hypoeutectic High Chromium Cast Iron
浇注温度对半固态亚共晶高铬铸铁初生奥氏体的影响
5.
Effects of Pouring Temperature and Mechanical Vibration to Microstructure and Mechanical Properties of Lost Foam Casting Magnesium Alloy
浇注温度和机械振动对消失模铸造镁合金组织和力学性能的影响
6.
The Effect of Casting Temperature on Continuous Rheo-Extrusion of AZ31 Alloy based on Numerical Simulation
基于数值模拟的AZ31镁合金连续流变成形浇注温度的影响
7.
Effect of Casting Temperature on the Mechanical Properties and Microstructures of the ZL210A Casting Aluminum Alloy
浇注温度对ZL210A铸造铝合金铸态力学性能和微观组织的影响
8.
Effects of Pouring Temperature on Solidification Behavior of Aluminum Alloy Melt with Electromagnetic Stirring
电磁搅拌铝合金热模浇注温度对其凝固行为的影响
9.
Fabrication and Mechanism of Non-dendrite Structure in Semi-solid ZL101 Alloy by Controlled Pouring Temperature
控制浇注温度制备的半固态ZL101合金的非枝晶组织
10.
Effect of Heat Treatment Temperature on Properties of Lightweight Castable
热处理温度对轻质浇注料性能的影响
11.
Effect of Heat Treatment Temperature on Property of Mullite-Bauxite Castable Refractory
热处理温度对莫来石-铝矾土浇注料性能的影响
12.
Effect of Heat Treatment Temperature on Properties of Calcined Flint Clay-Bauxite Castable Refractory
热处理温度对焦宝石-铝矾土浇注料性能的影响
13.
"Different insulation materials such as refractory, refractory castable and fiber insulation materials are used in different zones."
炉子的保温材料根据炉子温度要求不同,分别选用耐火砖,耐火浇注料,纤维保温材料。
14.
In this paper, the temperature field of Sodium silicate sand cores of the machine tool＇ s cast iron is measured.
本文对机床铸铁件水玻璃砂芯在浇注、却过程中的温度场进行了测定。
15.
Research on Golf-Shaped Bubble Bauxite Insulating Castables
高尔夫球型高铝空心球保温浇注料的研制
16.
Rebuilding a Electric Control System of HLZ10C Piston Casting Machine
HLZ10C型活塞浇注机电气控制系统温控改进设计
17.
The influence of the filler-asphalt ratio on the high-and-low-temperature performance of gussasphalt mortar
粉胶比对浇注式沥青胶浆高低温性能的影响
18.
Simulating Analysis of Concrete Steep Slope Dam Thermal Stresses during Hyperthermia Seasons
高温季节浇筑陡坡坝段温度应力仿真研究