1.
So makers have had to adjust their knives accordingly.
对此，制刀者也必须相应地对刀调整。
2.
On Tool Setting by Test Cutting and Tool Compensation Adjusting in CNC Lathe;
数控车床试切对刀及刀补修调的研究
3.
Discussion on presetting cutter of CJK6032 CNC latfae andinput of offset error of cutting tool;
CJK6032A数控车床的对刀及刀偏值的输入
4.
Principles and General Service Methods of Presetting Cutter in HNC Lathe
数控机床的对刀原理及常用的对刀方法
5.
Practical Methods of Tool Setting on CNC Lathe and Application of Tool Compensation
数控车床实用对刀方法及刀具补偿的应用
6.
The reliability of batch of tools can be improved by screening test.
利用可靠性筛选试验对刀具进行预选,可以提高一批刀具的可靠性。
7.
Possessing a speed blades gap adjustingdevice, permit to adjust steplessly the blades gap.
刀片间隙快速调整机构，可对刀口间隙进行无级调整。
8.
There are5 active buttons and actoiive baffles that move left and right. Please press the active button as you need.
磨刀在手动状态时，按下所要磨刀的对应按钮。如果5把刀同时要磨刀，就按整体磨刀按钮。
9.
This be not a tin opener, be it ?
这不是罐头刀，对吗?
10.
remove body hair with a razor.
用剃刀对身体进行脱毛。
11.
The Influence of Design of Hob Cutter Tip on Teeth Bending Strength;
滚刀刀顶设计及对齿根弯曲强度的影响
12.
So improvements of the obdurability of the tool tips and cutting edges are very important to better the cutting property of the end mill.
刀尖是刀具中最薄弱的环节，提高刀尖及切削刃的强韧性对改善刀具切削性能尤其重要。
13.
The cutter location arithmetic for sphere milling cutter and flat-end milling cutter is pointed out and the tool path of vane surface is simulated.
提出了球头刀和平头刀的刀位计算方法,并对叶片曲面的刀具轨迹进行了仿真模拟。
14.
Test for any wobble of the blade at the pivot. This is often considered an important test of a folder's construction especially if it is knife which will see use.
测试刀体在刀轴上是否有晃动，这是公认的对折叠刀结构的重要测试，特别是你要使用这把刀。
15.
Please check the up-cutter-head of knife at the notch part is whether rightly opposite to the necking of down-cutter-head or not ,and no binding phenomenon.
请检查开槽部上刀盘的刀片是否与下刀盘的刀槽对正,运行时无卡滞现象.
16.
Pattern Notches: The pattern cutter has a pair of pattern notches which are used for marking seam allowances and balance marks.
样板刀眼剪刀：每个样板师都有一把样板刀眼剪刀,用来剪缝份(放松量)和对位记号。
17.
Weapons 2 men forms: Different forms all using the saber, the spear, the stick the sword and others.
六、器械对练：对砍十三刀，对八卦刀，对扎六枪，迎手棍，划大杆，对剑等。
18.
Legal Thinking on Dealing with the Question of the Scissors Gap between Industry and Agriculture of Prices;
应对工农剪刀差问题的法律对策研究