说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 句库 -> 尺寸选择
1.
Guide for choosing modular dimensions for waveguide components
GB/T11321-1989波导元件模数尺寸选择指南
2.
This was the primary reason for selecting the fin size for the Saturn Vehicle.
这就是“土星”飞行器安定面尺寸选择的主要依据。
3.
Selectivity study on minimum mesh size of bottom trawl codend in South China Sea
南海区拖网网囊最小网目尺寸选择性研究
4.
Surface Modification, Size Choice and Fluorescent Sensing of CdTe Quantum Dots;
CdTe量子点的表面修饰、尺寸选择与荧光传感
5.
Discussion of Size Choice of Loss Button Suppressing Band-Edge Oscillation
衰减钮扣抑制振荡技术尺寸选择的探讨
6.
Performance Analysis of Large-Aperture Receiving and Selection of Aperture Size in Atmospheric Optical Communications
大气光通信中大孔径接收性能分析与孔径尺寸选择
7.
If the tire size is incorrect, depress the Enter key and then select the correct size.
如果轮胎尺寸不对,按回车键,然后选择正确尺寸。
8.
A difficult measurement to take, and therefore you are advised to use the size chart by measuring the model's bust size and then selecting the average measurement given.
难量的尺寸,可以用尺寸图。量模特的胸围尺寸,然后选择一个平均数。
9.
Arcylic container and stainless steel pump, has two sizes for your choice.
集装箱、锈钢泵共聚,你有两个选择尺寸.
10.
undersized slot concept
选择偏小割缝尺寸的设计概念
11.
The current page size is larger than the size of the special paper. Choose another page size to use the Special Paper option.
当前页面尺寸大于特殊纸张的尺寸。请选择其他页面尺寸,以便使用“特殊纸张”选项。
12.
Take body measurements and select the pattern size based on the following measurements: for the jacket uses the chest measurement, and for the trousers use the hip measurement.
按照如下的方法测体并选择样板尺寸:上装量胸围尺寸;裤子量臀围尺寸。
13.
Describes the calculations needed to choose the optimum motor, wheel and winch sizes.
描述选择最优马达、和绞盘尺寸所需的计算。
14.
Preliminary Design. The initial selection of member sizes is called "preliminary design".
初步设计。构件尺寸的初步选择叫做"初步设计"。
15.
Efficient Analysis of Conformal Frequency Selective Surfaces by Characteristic Basis Function Method and the Adaptive Cross Approximation Algorithm
CBFM-ACA方法快速分析有限尺寸共形频率选择表面
16.
Select from the standard light fitting sizes, or choose (Custom) and stretch to desired size.
从标准灯具尺寸中选择,或选择(自定义)然后拉伸到所需大小。
17.
Co-ordination of dimensions in ships' accommodation--Selection of components and assemblies sizes and assembly
GB/T7386.3-1987船舶起居舱室的尺度协调元件和组件尺寸的选择及组装
18.
Selections of views and representation methods must be proper, dimensions be reasonable and technical requirements be correct.
零件的视图选择、表达方法要正确、尺寸标注要合理,技术要求要正确。