1.
After the transformation of the shift flow to the total low-temperature shift process, the steam consumption per ton of ammonia drops remarkably, but the resistance in the catalyst beds increases rapidly.
将变换流程改为全低变工艺后，吨氨蒸汽消耗明显下降，但触媒床层阻力迅速上升。
2.
Medium-Low-Low Temperature Shift Conversion Process and Para-Zero Steam Consumption Technology
中-低-低变换工艺和准零汽耗技术
3.
Application of CO Low-temperature Conversion Process to Gas Production
CO低温变换工艺在燃气生产的应用
4.
Using protection cast process in the whole course to debase the content of gas and inclusion.
采用全程保护浇注工艺降低气体和夹杂物含量 ;
5.
Effects of Welding Process on Cryogenic Safety of Welded Joint of 16MnR Steel
焊接工艺对16MnR钢焊接接头低温安全性的影响
6.
Design of Low Noise Amplifier and Down-Convert Mixer Based on 0.18μm CMOS Technologe Used in 5GHz WLAN;
0.18μm CMOS工艺5GHz WLAN低噪声放大器和下变频器的设计
7.
Study on Austempering Process Parameters of Modified Low Chromium White Cast Iron
低铬变质白口铸铁等温淬火工艺参数的研究
8.
Industrial Use of New Process of Low Water-Gas Ratio Shift Conversion with Sulfur-Resistant Catalyst in Shell Pulverized Coal Gasifier
低水气比耐硫变换新工艺在Shell粉煤气化装置上的工业应用
9.
at is concluded that by this process bright Zn plating can be provided with high deposition rate, low cost and reliable quality.
结论是本工艺可镀出全光亮的锌镀层、沉积速度快、成本低,质量稳定。
10.
Process Optimization and Quality Control of Full Chilled Low Alloy Casting Iron Camshaft;
全激冷低合金铸铁凸轮轴的工艺优化与质量控制
11.
Process Parameters on the Microstructure Evolution of a Low Carbon Microalloyed High Strength Dual Phase Steel;
工艺参数对低碳微合金高强度双相钢显微组织演变的影响
12.
Annealing texture of CSP low carbon steel sheet under different cold rolling reduction ratio
CSP工艺不同冷轧压下率低碳钢板退火织构的演变
13.
For the low guality and high cost of wear structur al parts, especially gear wheel, the new technology of variable temperature and low-pressure carborization is indicated.
针对耐磨构件，尤其是齿轮等机械构件质量低和生产成本高的现状，提出变温低压渗碳新工艺。
14.
These artefacts are correctives to the usual view of these people as completely uncivilized.
通常认为这些人完全没有开化, 这些工艺品改变了人们的这种看法.
15.
Screening the processing of low-sugar preserved fruit of seed used watermelon peel
低糖籽瓜皮果脯加工工艺条件的筛选
16.
Use Low Oxygen Copper Rod as Feedstock to extrude ProductsBy CONFORM Machine
Conform挤压机采用低氧电工铜杆工艺试验
17.
The safety problems are more severe for low-pressure depositions because the processes often use concentrated gases.
对于低压淀积来说安全性问题更为突出，因为这种工艺通常使用高浓度的气体。
18.
By use of nondestructive testing methods and techniques it has been possible to decrease the factor of ignorance about material without decreasing the factor of safety in the finished product.
利用无损探伤方法和工艺，已使我们能在不降低成品安全系数的情况下，提高对材料的了解程度。