说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 句库 -> 真空差压铸造
1.
Modeling and Analysis of Vacuum Counter-Pressure Casting Based on Digital Combination Valve
基于数字组合阀的真空差压铸造系统建模分析
2.
Design of the Intelligent Vacuum Counter-pressure Casting Control System Based on PCI bus
基于PCI总线的真空差压铸造控制系统设计
3.
Process and Theory of Vacuum Counter-pressure Casting Thin-wall Aluminum Alloy Castings Based on Intelligent Control;
智能控制的薄壁铝合金铸件真空差压铸造工艺与理论
4.
Mould filling of low-pressure expendable pattern casting process for magnesium alloys
镁合金真空低压消失模铸造充型特征
5.
Research on Common Defects of Low-pressure Expendable Pattern Casting Process for Magnesium Alloy
镁合金真空低压消失模铸造常见缺陷分析
6.
Pressure-expendable Pattern Casting Process for Magnesium Alloy
镁合金真空低压消失模铸造的技术特征与实践
7.
Study on Adjusted Pressure Casting Process with Electromagnetic and Vacuum for Aluminum Alloy Casting of Complicated & Thin-wall Components
复杂薄壁铝合金铸件磁动力真空调压铸造工艺研究
8.
3D Design and Automation of Vacuum and Low Pressure-Expendable Pattern Casting Process Product Line
真空低压镁合金消失模铸造生产线的三维设计及自动控制
9.
Study on the Influencing Factors and Filling Ability of Magnesium Alloys in the Lost Foam Casting(LFC) with Vacuum and Low Pressure
镁合金真空低压消失模铸造影响因素及充型能力的研究
10.
Selection of Vacuum Pump and Capacity Calculation of Dust Separator in Lost Foam and V-process Casting
消失模与V法铸造用真空泵的选型和负压罐的计算
11.
Analysis on Thermodynamics and Kinetics of Vacuum Degassing from Aluminum Melt during Adjusted Pressure Casting
调压铸造中铝液真空除气的热力学和动力学分析
12.
Mechanism and Solution of Bonded Sand in Differential Pressure Casting
浅析差压铸造件粘砂机理及解决措施
13.
Study on the preparation of wear resistant surface cast by vacuum-full mould casting
真空实型铸造法制备表面耐磨铸件研究进展
14.
Design method of the vacuum die-casting mould for large-scale thin shell part
大型薄壁件真空压铸模具的设计方法
15.
Visualization of Vacuum Expandable Pattern Casting Plowshare by the ProCAST Software
基于ProCAST的犁铧真空实型铸造分析
16.
Centrifugal Casting of Cylinder Liner of Air Compressor Used for Mine Electric Locomotive
矿用电力机车空压机缸套的离心铸造
17.
The Mechanism of the Mold Collapse Defect for Iron Casting in Expendable Pattern Casting Process with Dry Sand and Vacuum
真空消失模铸造铸铁件铸型坍塌缺陷成因的研究
18.
Application of Vacuum and Partial Pressurization in Die Casting Automobile Components
抽真空及局部增压工艺在压铸生产上的实践