1.
The determination of cut height is key to blasting engineering fordemolishing reinforced concrete towering tubular buildings.
切口高度的确定是钢筋混凝土高耸筒形结构物爆破拆除的关键问题。
2.
Numerical Simulation of Precutting′s Angle and Height of Chimney Blasting
烟囱爆破切口角度高度数值模拟研究
3.
Theoretical analysis of the blasting cut length of dominant building;
高耸构筑物定向爆破切口长度理论分析
4.
Parameters about three dimensional modeling and parameters of wire electric machining in processing the auto-closed cut on the ring with high precision
高精度卡环接口三维建模与线切割参数研究
5.
Evaluation of Adhesion Strength of High-Strength Coating by Symmetrical-Incision Tensile Testing and Analysis of Its Plane Stress bv Finite Element Method
对称切口拉伸法评价高强度涂层及平面应力有限元分析
6.
Small incision cataract extraction and intraocular lens implantation in high myopia
高度近视白内障小切口摘出及人工晶状体植入术
7.
A cutting tool is wear-resistant if it resists abrasion at the cutting edge and along the tool face. Wear resistance improves as cutting tool hardness increases.
如果切削刀具的刃口和刀面耐磨,刀具就不易磨损。切削刀具的硬度越高,耐磨性就越好。
8.
basic crest truncation
基准螺纹牙顶切除高度
9.
The length of incision scar was only about 60% of median stemotomy.
疤痕长度仅为胸骨正中切口的60％左右。
10.
Difference of the Intension of Incision between Corneal Tunnel Incision and Sclera Tunnel Incision and the Study in Histopathology;
巩膜隧道切口与角膜隧道切口强度比较及组织病理学研究
11.
It was mainly composed of a grooving spring is located in the middle of the artificial vertebral body and the platforms are fixed to the upper and lower ends of the spring by forth-and-back hand thread.
切口弹簧与平台间以正、反向螺丝连接，通过旋转弹簧体可以调节平台的高度。
12.
Depending on your desire to play with this embouchure, you will experience difficulty in playing throat F, and high C.
取决于你对使用这个口型的热切程度，你会经历一段时间难以演奏鼻音F和高音C。
13.
Recently the imported porous polyethylene framework of high density has been used for external ear reconstruction by cutting and assembling in accordance with the shape of the normal ear.
或者采用进口的高密度多孔聚乙烯材料按健耳的大小和形状切削修整组装形成外耳支架。
14.
Leave the motorway at the Stokenchurch exit.
在斯托肯彻切出口处驶离高速公路.
15.
Do not whistle until you are out of the wood.
未出林涛，莫吹口哨。未脱险境，切莫高兴。
16.
MICROSTRUCTURE AND HARDNESS OF ADIABATIC SHEAR BANDS IN HIGH STRENGTH STEELS
高强度钢中绝热剪切带的组织和硬度
17.
Testing Method for Tensile and Shear Strength of High Strength Photosensitive Glue
高强度光敏胶拉伸剪切强度测试方法
18.
The height of the aperture and the full height, were also harmonically designed.
洞口高度和所有高度也一样和谐设计。