1.
Study on 1-D Large Scale Rough Surface EM Scattering at Low Grazing Incidence by Parallel MOM Based on MPI of PC Clusters
PC集群MPI并行矩量法研究一维大尺度粗糙面掠入射电磁散射特性
2.
The internal surface processing of hydraulic cylinder requires high accuracy of size, shape, and good deformed surface finish.
液压缸内表面要求较高的尺寸精度、状精度以及适宜的表面粗糙度。
3.
Comparison of rectangular orthodontic arch wires on size precision,surface roughness and sectional vertical angle arc
方形弓丝尺寸精度、表面粗糙度及拐角处弧度比较
4.
Analysis Method for Nanometer-Scale Line Edge Roughness Based on Stationary Wavelet Transform
基于平稳小波变换的纳米尺度线边缘粗糙度分析方法(英文)
5.
Comparative Study on Predicting Porosity by Different Roughness Indices
不同粗糙度尺度下预测表层土壤孔隙率量化指数比较研究
6.
General purpose screw threads-Limits of sizes for commercial bolt and nut threads-Coarse quality
GB/T9146-1988商品紧固件的粗糙级精度普通螺纹极限尺寸
7.
Competency in the use of measuring devices such as dimensional inspection tools, callipers, dial gauges, roughness tester and alike.
能运用数显卡尺，量规，粗糙度测量仪等仪器进行测量.
8.
Multiscale genetic algorithms for discretization in rough set on trees
粗糙集中连续属性基于树结构离散化的多尺度遗传算法
9.
A New Method for the Roughness Measure of a Fuzzy Set;
模糊粗糙集中依参数粗糙度的新算法
10.
It was found that the surface roughness is significant in Brinell hardness testing, but has little influence on Rockwell hardness.
结果表明,表面粗糙度对布氏硬度值有重要影响,而洛氏硬度值与表面粗糙度关系不大。
11.
STUDY ON SHEAR CREEP AND ROUGHNESS EFFECT ON HARD DISCONTINUITIES OF MARBLE
大理岩硬性结构面剪切蠕变及粗糙度效应研究
12.
P-rough integrals and the rough degree of function two-direction S-rough sets
P-粗积分与函数双向S-粗集的粗糙度
13.
The quick mark of the surface roughness in AutoCAD;
AutoCAD中表面粗糙度的标注
14.
The grinded roughness may be 40% of the roughness to be textured.
磨削而成的粗糙度可能是将要打毛粗糙度的40%？
15.
Variable precision rough sets and Bayesian classification of rough set image classification
变精度粗糙集与贝叶斯粗糙集图像分类研究
16.
The vertical extent of this layer in strong winds depends mainly on the roughness of the underlying terrain, but is usually many hundreds of feet.
强风产生的该层厚度主要与地形的粗糙程度有关，通常有好几百英尺。
17.
The surface roughness of bath bottom, depth of tin liquid and temperature all affect the bubble forming considerably.
槽底表面粗糙度、锡液深度及温度对气泡形成有很大影响。
18.
Standard finish of gasket surface is125-200 micro-inch maximum roughness.
垫圈表面的标准光洁度最大为125-200百万分之一英寸粗糙度。