1.
Development Of Evaporative Cooling Medium Of Electrical Equipmen And Research Experiment Of Evaporative Cooling Characteristic;
电器设备蒸发冷却介质的制备及其蒸发冷却特性的研究
2.
The same jacket or wall cavity is utilized during cooling of the product by introducing a cold medium and cooling the product contact surface.
同样利用容器的加套或空心壁在冷却产品时引入冷却介质,并且冷却产品的接触表面。
3.
The cooling section is the third heat exchanger of the system and is designed to use a cooling medium to reduce the product to the desired temperature, typically near the temperature at which it will be packaged and stored.
冷却段为设备中第三个热交换器,用冷却介质将产品降到要求的特别接近包装和储存的温度。
4.
In the past, air was the common cooling medium for components of most excitation systems.
过去,普遍采用空气作为励磁系统各部件的冷却介质。
5.
Other factors influencing the process are the size of the container and the types of heating and cooling media utilized.
其它影响加工的因素是容器的大小、加热类型和所采用冷却介质。
6.
Research on Heat Transfer Property Measuring System for Evaporation-Cooling Coolant and Concerning Experiments;
蒸发冷却介质凝结传热特性测试平台的研制及相关实验研究
7.
Experimental research of AC breakdown voltage of evaporative coolant under boiled two-phase-flow condition
蒸发冷却介质两相流状态下工频击穿特性的实验研究
8.
"The cooling agents customarily employed are air and a liquid (usually water), either alone or in combination."
所用冷却介质通常为空气和液体(主要是水),可以单独使用或联合使用。
9.
Preliminary Research on the Performance of an Evaporating Intercooling of Multiple-hole Material;
一种多孔介质蒸发冷却中冷器性能的初步研究
10.
The normal media are: steam, thermal oil, hot water and chill water.
常用介质有：水蒸汽、导热油、热水、冷却水等。
11.
Fundamentally Studies about Applying Porous Medium to a New Cooling Technique;
一种新型冷却技术中应用多孔介质的机理研究
12.
"design for energy fluids: fuel gas, inert gas, cooling water, compressed air and waste water"
能源介质设计(到接点):燃气、保护气、冷却水、压缩空气和废水;
13.
The cooling/ heating media is connected to the rolls through rotary joints with ball bearing and carbon seals for a leak free operation.
冷却/加热介质由旋转接头和辊连接，球轴承和密封圈保证不会泄漏。
14.
Design of a Cooling Characteristics Testing System for Quenching Media Based on Virtual Instrument;
基于虚拟仪器的淬火介质冷却特性测试系统设计
15.
Simulation of work characteristics of a new refrigerant VxF4310 in inner evaporative cooling system of 300MW turbine generator
新介质VxF4310在300MW蒸发冷却汽轮发电机中的工作特性模拟分析
16.
Conventional submersible non-clog pump motors are air-filled non-jacketed type designed to be cooled by convection heat transfer to the surrounding media.
一般的潜水无堵塞泵电机是风冷、无加套结构设计,由周围介质的对流传热进行冷却。
17.
Investigations on Nonlinear Properties of Light in Cold-Atom Medium
冷原子介质中非线性光学性质的研究
18.
The application of inverter in cooling tower fan system modification was introduced.
介绍了变频器在冷却塔风机系统改造中的应用。