说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 句库 -> 支座设计
1.
DESIGN OF CORNER COLUMN,JOIST AND SUPPORT ON THE EXISTING MAIN FACTORY BUILDING FOR A NEW MAIN FACTORY BUILDING
新厂房角柱、托梁及其在旧厂房上的支座设计
2.
The Research on Parameters Optimization of Seismic-isolated Bearings of Railway Steel Truss Arch Bridge
铁路钢桁拱桥减隔震支座设计参数的优化研究
3.
Design and Experimental Study of All Direction Bearings in Tanzania State Gymnasium
坦桑尼亚国家体育场万向支座设计及试验分析研究
4.
In this paper, the construction method for the hinged steel bearings and hinged sliding plate bearings specially designed for the Bridge is presented.
介绍针对本桥专门设计的铰轴钢支座和铰轴滑板钢支座施工方法。
5.
Method and Application of Process Optimization for Backup Roll Chocks;
支承辊轴承座工艺优化设计方法与应用
6.
DESIGN AND FINITE ELEMENT ANALYSIS OF THE PIN SUPPORT OF THE TUBULAR TRUSS
某大型管桁架支座节点设计及有限元分析
7.
The Design Method of the Seismically Isolated Bridge by Lead Rubber Bearing Based on Energy Method
基于能量法的铅芯橡胶支座隔震桥梁设计方法
8.
Elastic-Plastic Energy Dissipating Bearing for Seismic Design of Self-anchored Suspension Bridge with Single Tower
弹塑性阻尼支座用于自锚式悬索桥减震设计
9.
A piece of furniture consisting of a seat, legs, back, and often arms, designed to accommodate one person.
椅子有底座、支撑腿和靠背的家具,通常带扶手,设计用来供一人坐
10.
PROBING IN RUBBER PLANK SUPPORTS DESIGNED ON THE EXHIBITION GALLERY OF XIAMEN UNIVERSITY ART EDUCATION COLLEGE
板式橡胶支座在厦门大学艺术教育学院展廊设计应用初探
11.
Destruct Analyse of Steel Trestle Bridge of Roll-on Roll-off Terminal and Design of Strengthening;
滚装船码头钢栈桥支座破坏原因分析及加固设计
12.
Parameter Design and Application Analysis of Three-Dimension Isolation Bearing
摩擦—弹簧三维复合隔震支座的参数设计与应用研究
13.
Design and Construction of Anti-seismic Bearing in Long Span Continuous Bridge with High Piers
高墩铁路大跨度连续梁桥抗震支座的设计与施工
14.
Optimum Design of Support Brackets of Evaporators based on BP Neural Network and Improved Genetic Algorithm
基于BP神经网络和改进遗传算法的蒸发器支座结构优化设计
15.
Design and Performance Tests of Combined Disk Spring Bearing for Vertical-isolated Buildings
组合式碟形弹簧竖向隔震支座的设计与性能试验研究
16.
Join welding technology and high-strength bolts details of this technology standards.
屋架支架支座、撑系统的构造做法需认真检查,必须符合设计要求,零配件不得遗漏。
17.
The pressurizer is supported by the butt-welded connection between the integrated forged boss on the lower endplate and supporting cylinder on the skirt support.
稳压器的支承设计采用下封头整体锻出的凸台与裙座支承筒对接焊连接。
18.
He assisted in designing the new bridge.
他协助设计那座新桥。