说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 句库 -> 塑性铰模型
1.
SEISMIC DAMAGE EVALUATION OF RC BRIDGE COLUMNS BASED ON PLASTIC HINGE MODEL
基于塑性铰模型的钢筋混凝土桥墩地震损伤评价
2.
The plastic elemental stiffness matrix was derived by plastic-hinge method.
然后用塑性铰法推导了单元的塑性刚度矩阵。
3.
Yield-line Theory Application and Studying of Thin Plate Curve Problem;
薄板弯曲问题的塑性铰线法应用研究
4.
Solution Method for Anti-blast Ability of the Wall Based on Yield Line Theory
利用塑性铰线理论求解墙体抗爆能力
5.
If the order of buckle or plastic kings is different, the failure modal is different.
构件失稳或形成塑性铰的顺序不同即失效路径不同,失效模式的安全余量也不同。
6.
Respond Analysis and Modelling of the Articulated Car Body Considering the Effect of Elasticity for High Speed Train
考虑车体弹性的铰接式高速车辆模型及响应计算分析
7.
Research on Peripheral Spring Foundation-Straight Beam-Spring Hinge Numerical Model of Shield Tunnel Segment Design;
全周弹簧—直梁—弹性铰数值模型在盾构管片设计中的研究
8.
Design of Plastic Pipe’s Expanding Die Based on Four-Bar Linkages
基于铰链四杆机构的塑料管材扩口模具设计
9.
In-Plane Nonlinear Theory and Elastic-Plastic Stability of Pined Circular Arches;
两铰圆弧拱非线性弯曲理论和弹塑性稳定
10.
The Property and Formation of the Plastic Hinge in Rotary Forging and Upsetting Process of Ring Billet
摆辗镦粗工艺过程中塑性铰形成与特性研究
11.
After the inelastic phase, the distributing of plastic hinges is proper and reasonable, and the requirement of ductility design of structure is satisfied.
进入塑性阶段后,塑性铰分布合理,满足了结构延性设计的要求。
12.
The ultimate load of plate girders was analyzed by spline finite strip and plastic hinge method.
用样条有限条塑性铰法分析了板梁的极限荷载。
13.
Shear Capacity of Plastic Hinge Region of RC Shear Wall;
钢筋混凝土剪力墙塑性铰区受剪承载力分析
14.
The Analysis of Pile-Soil-Structure Dynamical Interaction Based on Plastic Hinge Theory;
基于塑性铰理论的桩—土—结构动力相互作用分析
15.
Quasi-Static Cyclic Tests and Plastic Hinge Analysis of RC Structural Walls
钢筋混凝土墙准静力循环试验和塑性铰分析
16.
Molecular Dynamics Simulation of Superplasticity Model for Nano-Crystal;
纳米晶超塑性模型的分子动力学模拟
17.
Viscoelastic Constitutive Model of In-Mould Decoration Films
模内镶件注塑膜片的粘弹性本构模型
18.
Experiment and Numerical Simulation Research of the Injection Molding Characteristic for Thin-Wall Plastic Parts;
薄壁塑件注塑成型特性的试验与数值模拟研究