1.
A Study of Blunted-Wedge Holder and It s Application in CARDC s Arc-Heated Wind Tunnel;
电弧风洞钝楔试验技术及其应用研究
2.
Technological Experimental Research for Cross Wedge Rolling Technology of Pin Valve of Oil Pump
油泵油嘴针阀体楔横轧工艺试验研究
3.
A Primary Report on the Control of Saperda balsamifera Motschulsky by Scleroderma guani
管氏肿腿蜂防治锈斑楔天牛试验初报
4.
Photographic films and papers Wedge test for brittleness
GB/T6849-1995照相胶片和相纸脆性楔式试验方法
5.
Control Saperda populnea with 16% Chongxianqing EC
利用16%虫线清乳油防治青杨楔天牛试验初报
6.
An Experimental Study on the Nonlinear Characteristics of the Ringed-wedge Connection Structure;
楔形环连接结构非线性动力学特性试验研究
7.
Theoretic and Experimental Research on Three-Roll Cross Wedge Rolling of Non-Quenched and Tempered Steel Hollow Shafts
非调质钢空心轴三辊楔横轧理论与试验研究
8.
"Valve body, bonnet and wedge are to be of bronze aSTM B 62."
阀体,阀盖和楔板材质符合美国材料试验协会aSTMB62标准青铜。
9.
Research on Optimizing Design of Poly-rib Belt Driving Wheel System and Development of Test-bed;
发动机多楔带轮系优化的研究及试验台架的开发
10.
The effect of support on concrete fracture toughness in wedge-splitting test
楔入劈拉试验支承形式对混凝土断裂韧度的影响
11.
Hysteresis of tapered H-section steel short beam with thin web under cyclic loadⅠ:experiment
低周往复荷载下楔形H形钢短梁滞回性能Ⅰ:试验研究
12.
V-and ribbed belt drives--Dynamic test to determine pitch zone location--Part 1: V-belts
GB/T17516.1-1998V带和多楔带传动测定节面位置的动态试验方法第1部分:V带
13.
In the first part, we researched the anchorage system of CFRP and made a kind of new-type wedge anchor.
在试验中，首先对碳纤维塑料筋锚固系统进行探索性研究，研制出一种新型楔块式锚具；
14.
Experimental Study of Flow Characteristics of Salinity Intrusion and the Influence on the Heated Discharge of Power Plant in Fresh and Salt Water Mixing;
盐淡水交汇水域盐水楔运动规律及其对电厂温排水影响的试验研究
15.
Analysis and Testing of Wedge-and-Strip Anode Detector Characteristics
楔条形阳极探测器的性能测试与分析
16.
During the tests we did not successfully extract any picokeystones.
在测试期间我们没有成功的提取出一块微楔石。
17.
Research on Fracture Parameters for Non-standard Wedge Splitting Specimen of Concrete
非标准楔入劈拉试件研究混凝土的断裂参数
18.
Finite Element Simulation of Deformation Behavior of Preform Designed Workpiece During Equal Channel Angular Pressing
楔形头部试样的ECAP变形行为有限元模拟