1.
Studies on Stomata Length,Width and Density of Different Provenances of Distylium buxifolium
不同种源小叶蚊母气孔长度、宽度与密度的关系
2.
Study on Slender Hole Ultra-precision Measuring System and Precision Analysis;
细长小孔孔径精密测量系统的设计及精度分析
3.
Study on the Reliability of the Auger Bored Cast-with-pressure Concrete Pile
长螺旋钻孔压灌混凝土桩可靠度研究
4.
Study on the Measurement of Roundness and Straightness for the Inner Hole of the Large Diameter Long Pipes;
大口径长管内孔的直线度、圆度测量研究
5.
Most of the germinal apertures were 3 couples, distributed symmetrically at the three sides by the axis of symmetry of the tetrahedron.
萌发孔沟的长度、宽度、孔盖长宽与形状、突起的程度等，在个体间有差异。
6.
The cross-sectional areas of the pore openings vary along their length.
孔隙通道的横截面面积沿其长度方向变化。
7.
Experimental analysis of artificial deep foundation with large diameter and length shorter than 6 metres
长度小于6m的大直径人工挖孔深基础试验研究
8.
Dynamic Scaling in Growth of Holes in Ballistic Deposition Model
Ballistic Deposition模型孔洞生长标度行为的数值模拟
9.
Study on the Effect of Length and Arrangement of Carbon Fiber on Carbon Paper Pore Structure
炭纤维长度和排布对炭纸孔隙结构的影响研究
10.
Estimation of Reservoir Porosity Parameter Using Array Sonic Wave Slowness
应用阵列声波长源距声波时差求取孔隙度参数
11.
The size of the filament is also controlled by varying the rate at which the filaments are pulled away from the hole by the godet wheel.
长丝的直径还与导丝盘从喷丝头孔引离长丝时的速度有关。
12.
Installing bolts allowed to use gas cutting bore hole and never more than two gaskets pad not sexual bolts, exposed screw bolt length of not less than2-3 deduction.
安装螺栓孔不允许用气割扩孔,永乆性螺栓不得垫两个以上垫圈,螺栓外露丝扣长度不少于2～扣.
13.
Before installing the valve, be sure that the pipe ends are reamed and threads are cut to size.
在安装阀门之前，要确保管道末端经过铰孔，螺纹长度切割适中。
14.
Before installing, be sure pipe ends are reamed and threads are cut to size.
在安装之前，要确保管道连接端已经经过铰孔，螺纹有足够的长度。
15.
The girl wore a long dress of peacock-green gauze lined with white silk.
女的是一身孔雀翠华尔纱面子，白印度绸里子的长旗袍。
16.
The method for measurement of the length of stoma guard cell could be used to identify ploidy.
因此可利用测量气孔保卫细胞长度的方法鉴定花粉植株的倍性.
17.
Computer Aided Optimum Design of Die Bearing Length and Layout for Aluminium Profile Extrusion
铝型材挤压模工作带长度和模孔配置的优化设计
18.
Keep proper length of pipe when put into the manhole.
布放后应保留适当长度于引进端人(手)孔或拉箱内。