1.
To harden the surface or case of(iron or steel) by high-temperature shallow infusion of carbon followed by quenching.
表面渗碳硬化法通过高温条件下对碳的浅层注入并紧接冷却来使（铁或钢的）表面或外壳硬化
2.
To treat, combine, or impregnate with carbon, as when casehardening steel.
使渗碳，碳化使与碳一起处理，使与碳混合或使充满碳，如将钢的表面粹火硬化
3.
"carburize:To treat, combine, or impregnate with carbon, as when casehardening steel."
使渗碳,碳化:使与碳一起处理,使与碳混合或使充满碳,如将钢的表面粹火硬化.
4.
Study on Equipment and Process of Plasma Carburizing Surface Hardening of Austenitic Stainless Steel at Low Temperature
奥氏体不锈钢低温离子渗碳表面硬化处理设备及工艺研究
5.
Microstructure and Hardness of Cr,B,C Ternary Cast-infiltrated on 45 Steel Surface
45钢表面铬、硼、碳三元铸渗层的组织和硬度
6.
Research of Middle Temperature Chromizing on Carbon Steel with Double Glow Plasma Surface Alloying Process and Carbon Migration in the Chromized Layer;
碳钢表面中温双辉等离子渗铬合金化及渗层中碳迁移的研究
7.
Electrochemical Brightening Process Optimization of Plasma Carburized Stainless Steel
离子渗碳不锈钢表面电化学亮化工艺的优化
8.
Refinement mechanicm of cementite phase in the process of surface nanocrystallization of 38CrSi steel
38CrSi合金钢表面纳米化中渗碳体相的细化分析
9.
Research on Structure and Properties of Alloyed Layer by Cast Penetrating on Medium Carbon Steel Surface
中碳钢表面铸渗合金化层组织和性能研究
10.
Double Glow Plasma Low Temperature Surface Chromizing Hardening Process of T10 Steel
T10钢低温双辉等离子表面渗镀铬硬化的研究
11.
Effect of Surface Brightening Methods on the Morphology and Corrosion Resistance of Plasma Carburized Stainless Steel
不锈钢离子渗碳后表面亮化处理方法对渗层形貌和性能的影响
12.
INVESTIGATION OF THE ACCURATE CONTROL ABOUTSURFACE CARBON CONCENTRATION OF CARBURISING PART
渗碳零件表面碳浓度精确控制的探讨
13.
Measurement on the carbonizing or nitro-caburizing harden case depth of sintering iron-based material
GB/T9095-1988烧结铁基材料渗碳或碳氮共渗硬化层深度的测定
14.
The Influence of Medium and Low Carbon Surface Nanocrystallization to Low Temperature Gas Nitriding;
中低碳钢表面纳米化对低温气体渗氮行为的影响
15.
Study on Brightening Treatment of Austenitic Stainless Steel after Low Temperature Plasma Carburizing
低温离子渗碳奥氏体不锈钢表面亮化处理的研究
16.
Two-step nitrocarburizing process to obtain the single-phase ε compound layer on steel surface
钢表面获得单相ε化合物层的二段氮碳共渗工艺
17.
Influence on Micro-structure and Surface Peening for TC4 of Carbonization Techniques
渗碳工艺对钛合金TC4板显微组织和表面强化的影响
18.
Influence of Strengthening Shot Peening on Formation and Extension of Fatigue Crack in Carburized Gear Surface
强化喷丸对渗碳齿轮表面接触疲劳裂纹形成与扩展的影响