1.
valve rocker shaft oil pipe adapter
气门摇臂轴油管接头
2.
Sometimes the camshaft is fitted directly into the cylinder head and operates on the valves without rockers.
有时，凸轮轴直接安装在气缸盖上并且不用摇臂控制阀门工作。
3.
"With this arrangement, the camshaft is directly below the valve lifter, and no push rods or rocker arms are necessary. "
"在这种装置中,凸轮轴直接装在气门挺杆下,并且不必有推杆或摇臂。"
4.
Reason Causing Blowhole in Headstock Housing of Radial Drilling Machine and its Prevention
摇臂钻床主轴箱体气孔产生原因及消除措施
5.
The cylinder head carries the valves, valve springs and the rockers on the rocker shaft, this part of the valve gear being worked by the push-rods.
气缸盖携带阀门，气门弹簧和在摇臂杆上的摇臂，这部分的气门传动机构通过推杆工作。
6.
parallel arm installation type [door closer]
平行臂式〔门气鼓〕
7.
Install the push rods, rocker arms, pivots and bridges in the order they were remove
按照拆卸顺序安装推杆、摇臂、枢轴和桥臂。
8.
Install pitman shaft and side cover in the housing.
在机座中安装转向摇臂轴和侧盖。
9.
Precise 3D Modeling of Design of Arm Shaft;
转向摇臂轴的精确三维造型设计应用
10.
"Essentially, the steering gear consists of two parts, a worm on the end of the steering shaft and a pitmanarm shaft on which there is a gear sector, toothed roller, or stud."
转向器基本上由两部分组成:装在转向轴末端的蜗杆和转向摇臂轴。
11.
The roof was beginning to fall in; the door was off its hinges; the rooms were empty and bare.
屋顶摇摇欲坠，门已经脱出了门轴，屋里空空荡荡，一无所有。
12.
Optimization of Cam and Rocker Arm of Engine Valve Train
发动机配气机构凸轮与摇臂的改进设计
13.
Install the engine cylinder head, push rods, rocker arms, bridges, pivots and engine cylinder head cover.
安装引擎汽缸盖、推杆、摇臂、桥、枢轴和引擎汽缸盖罩。
14.
"The gear sector, toothed roller, or stud meshes with the worm."
转向摇臂轴上装有扇形齿轮、带齿滚柱或指销,用以和蜗杆啮合。
15.
universal raidial milling machine(horizontal)
万能摇臂铣床（卧）
16.
"Valve Service and Maintenance includes installing new seat inserts, cleaning or replacing valve guides, servicing the camshaft and camshaft bearings, and timing the valves."
气门维修包括镶配气门座,清洁或更换气门导管,保养凸轮轴和凸轮轴轴承,气门的正时调整。
17.
Modeling and Simulating for Drive System of a 3-axis Electric Swing Test Bench
三轴电气摇摆试验台传动系统的建模与仿真
18.
"There are two general types of power steering. One type is self-contained, with all hydraulic pressure applied to the pitman arm shaft."
动力转向一般具有两种类型。一种是独立的,所有的液压力都施加在摇臂轴上。