1.
power tubing tongs with rollover feature
带压紧轮的动力油管钳
2.
Using a hose pinch-off pliers (C-4390), pinch power steering oil return hose off between the crossmember coupling and the pump.
使用软管夹紧钳(C-4390)，夹紧介于横梁联结与油泵之间的动力转向系统回油软管。
3.
Relations between the Vortex and Pressure Fluctuation in Draft Tube of the Hydraulic Turbine;
水轮机尾水管涡带与压力脉动的关系
4.
Hydraulic pump is the power unit of the hydraulic puller (hydraulic press, hydraulic pipe bender, hydraulic jack).
油压泵是油压拉出器（油压机、油压弯管机、油压千斤顶）的动力装置。
5.
Hydraulic pump is the power unit of the hydraulic puller(hudraulis press, hydraulic pipe bender, hydraulic jack).
油压泵是油压拉出器(油压机,油压弯管机,油压千斤顶)的动力装置.
6.
The Analysis of Tubing Thread Failure Mechanism and the Technology Reformation of Hydraulic Tong;
油管螺纹失效机理分析及液压钳的技术改造
7.
DESIGN AND CALCULATION OF THE CLIP OF THE POWER MOTOR TEST STAND USED IN THE WELL
井底动力马达试验台架夹紧钳的设计和计算
8.
gear oil pump with connecting bend pipe
带连接弯管的齿轮油泵
9.
Reducing the pressure fluctuation of synthetic gas for gas turbine when oil and synthetic gas exchange
减小燃气轮机油气切换时的燃气压力波动
10.
With a wrench he loosens the nuts which fuse the fuel line between tank and engine.
他用钳子扭松了接连油箱与发动机的油管上的螺钉帽。
11.
a pulley on a shaft that presses against a guide belt to guide or tighten it.
积压引导带引导或拴紧的放在架子上的滑轮。
12.
The initial gushing of oil out of a drill pipe is caused by the pressure of the gas trapped and compressed immediately above the oil deposits.
最初石油喷出钻管，是由于受到紧压在石油层上的被密封的气体的压力。
13.
Dynamic performance analysis of low pressure turbine(LPT) component with damping-sleeves
带阻尼套筒的某型发动机低压涡轮部件的动力特性分析
14.
pulling-in dogs
(拉拔用的)夹料钳，牵引链钳，带头线钳
15.
Bring the walking foot as close to presser foot 3 as possible to the extent that it does not come in contact with the rear face of presser foot. Securely tighten screw 2 in the center shaft bell crank.
移动外压脚，一直移动到不能顶到中压脚3的背面的位置，紧紧地拧紧中轴轮紧固螺丝
16.
Effect of start-up pressure gradient on steam channeling within heat condensate zones in the Bingham and monoclinal heavy oil reservoirs
宾汉型稠油单斜油藏热凝析带启动压力梯度对汽窜的影响
17.
A In-Pipette Pneumatic Micro-pressure Control System for Giga-Ohm Seal of Patch Clamp
膜片钳实验中吉欧封接的电极内气动微压力控制系统
18.
Design of Hydraulic Automatic Tension Device of Belt Conveyor
带式输送机液压自动拉紧装置的设计