1.
With sequential access, processing begins with relative record 0, then moves to relative record 1, 2, and so on.
采用顺序存取，从第0个相对记录开始，然后移到第一个，第二个......以此类似。
2.
{0} {1}-{2} of {3}, sorted by release date
第{1}个到第{2}个{0}，共{3}个(按发布日期排序)
3.
The file's first record (relative record 0) is at "start of file plus 0";
文件的第一个记录（相对记录编号为0）是在文件的起点上加0，
4.
The first factor on the right-hand side is of the order of prebuckling strain ??
右边的第一个因子跟屈前的应变?槭峭0一量级。
5.
A virgin material can be "started" from point 0 into either the first or the third quadrant.
一个没有用过的材料可以从0点“开始”进入第一或第三象限。
6.
A second instance of "^0" can't be created because it contains multiple data segments that were not marked as read only.
无法运行 “^0” 的第二个例程，因为它包含多个未标记为只读的数据段。
7.
Assume a file begins at track 30, sector 0, and that one logical record is stored in each sector.
假设一个文件从第30磁道第0扇区开始存放，并在每个扇区上存放一个逻辑记录，
8.
Grub counts everything from 0 so to boot a system at the 9th partition of the 2nd disk is root
从0开始计算每件事，所以要引导一个在第2块硬盘上第9分区的系统命令是“root
9.
We beat them 2-0 very comfortably and we scored a third, an amazing goal from Crespo that the linesman did not give.
我们2:0完胜他们，我们有第三个进球，克雷斯波的一个相当惊奇的进球，被边裁给抹杀了。”
10.
Three types of prizes will be given:1 first prize worth$100,2 second prizes worth$50 each; and5 third prizes worth$10 each.
分别为：第一名一位$00，第二名两位各$0，第三名五位各$0。
11.
Abu Dhabi, Muscat, Tbilisi\0Arabian Standard Time\0Arabian Daylight Time\0*
阿布扎比，马斯喀特，第比利斯\0阿拉伯标准时间\0阿拉伯夏时制\0*
12.
"Layer 3 protocol should be between 0 and 255.\0
"第三层通讯协议应该介于0和255之间。\0
13.
Bit 0 - 2 (last digit) - values range from 0 to 7.
第0-2位（最后一位数）--取值范围为0到7。
14.
"Layer 2 protocol should be between 0 and 255.\0
"第二层通讯协议应该介于0和255之间。\0
15.
Bit 0 - 2 (last digit) = Values range from 0 to 7.
第 0 - 2 位(最后一位数) = 取值范围为 0 到 7。
16.
Receive handler not specified for receive location "{0}"; updating with first receive handler with matching transport type.
没有为接收位置“{0}”指定接收处理程序；使用具有匹配传输类型的第一个接收处理程序更新。
17.
The sort reference is not valid. Make sure that it's within the data you want to sort, and the first Sort By box isn't the same or blank.\0
此排序引用无效。请确保其在所要排序的数据内，并且第一个"排序依据"框不相同且不为空。\0
18.
It is also useful when using selective display, because a plus sign bitmap can be displayed on line "0".
另外在使用有选择的显示功能时也是有帮助的，因为一个加号可以显示在第0行。