1.
Research on Non-equalization Machining Method for Cylindrical Cam Manufacturing Cylindrical Surfaces with Ring of Arc Groove
在圆柱面上加工环形圆弧凹槽的新方法研究
2.
"Single curved moldings include the cavetto (concave, with a quarter-circle profile), scotia (deep concave), flute (grooved),"
单曲线脚包括凹弧饰(具有四分之一圆的轮廓的凹面)、凹形边饰(深凹面)、凹槽饰(开槽的)
3.
A groove around the cylinder of a bullet.
弹壳槽线一圈环绕着子弹的圆柱状凹槽
4.
Numerical simulation and deforming control of concave curvature flanging in automobile panels
汽车覆盖件内凹圆弧翻边仿真与变形控制研究
5.
Scattering of Plane P Wave in Circular-arc-shaped Canyon Topography:High-frequency Solution
圆弧状凹陷地形对平面P波的散射:高频解答
6.
Finte Element Analysis of the Deformation at Concave arc on 91 Model Double circular arc Tooth Profile
91型双圆弧齿轮凹弧单点啮合变形的有限元分析
7.
one-fourth concave arc milling cutter
四分之一凹圆弧铣刀
8.
The circular arc wiring duct also called it separates wiring duct /the insulation wiring duct /seal type wiring duct /arc the circular arc wiring duct /walk wiring duct.
圆弧线槽也称之为圆弧型隔线槽/绝缘线槽/密封式线槽/弧线槽/走地线槽。
9.
Diffraction of Plane SH Waves by a Wedge-Shaped Medium with a Circular Canyon or Alluvial Valley;
含圆弧形凹陷或沉积的楔形场地对平面SH波的散射
10.
Notch- An indent on the edge of a wafer used for orientation purposes.
凹槽-晶圆片边缘上用于晶向定位的小凹槽。
11.
In simplest terms, piston rings are thin, circular pieces of metal that fit into grooves in the tops of the pistons.
简单地讲，活塞环就是装在活塞顶部的凹槽里的薄，圆的金属。
12.
Thin, circular, steel bands fit into grooves around the piston to seal the bottom of the combustion chamber.
把薄的，圆形的，钢圈放进活塞周围的凹槽以密封燃烧室的底部。
13.
The worn wheel tyre contact surface has a concave revolutionary curved form with two principal curvatures.
磨耗后的车轮接触面,是内凹圆弧的旋转形成面,有两种主曲率。
14.
Design for a new type of cam mechanisms-disk cam mechanism with concave arc follower(一)
一种新型凸轮机构——凹圆弧底从动件盘形凸轮机构的设计(一)
15.
<title>Minimum dimension design of disc cam mechanism with upright installed concave arc bottomed translating follower
正置式凹圆弧底直动从动件盘形凸轮机构的最小尺寸设计
16.
Dynamic Response of Circular-arc-shaped Canyon under the Incidence of Plane SH Wave:High-frequency Solution
圆弧状凹陷地形在平面SH波入射下的动力响应:高频解答
17.
Benches are equipped with either epoxy resin sink or polyolefin oval cupsinks while fume hoods are equipped with polyolefin cupsinks.
工作台配备环氧树脂水槽或聚稀烃类椭圆形杯槽。通风柜里也安装聚稀烃类椭圆形杯槽。
18.
The grooves into which they fit are called ring grooves.
安装活塞环的凹槽称为活塞环槽。