1.
Theoretical and Experimental Study of Secondary Moment on Concrete Frame Beams with External Pre-stressed Tendons;
体外预应力框架梁次弯矩的理论与实验研究
2.
The emphasis of the paper is placed on the influence of the secondary moment and the axial prestress on the moment redistribution.
重点讨论了预应力连续梁中次弯矩和轴向预压力对弯矩调幅的影响。
3.
Research into Secondary Moment and Redistribution of Internal Force about Bonded Post-Tensioned Prestressed Concrete Frame;
后张有粘结预应力混凝土框架次弯矩及内力重分布的研究
4.
Study on Secondary Moment and Redistribution of Internal Force about Continus Prestressing Concrete Hollow-core Slabs with Cold-drawn Low Carbon Wires
冷拔丝预应力砼连续多孔板的次弯矩及内力重分布研究
5.
It is shown that the secondary moment can facilitate the moment redistribution when the rotational capacity of plastic hinge is not enough.
从理论上证明了预应力次弯矩在塑性铰转动能力不够时能提高连续梁弯矩调幅能力的这一观点。
6.
Simulation of cold roll-bending of square pipe based on a secondary development from ANSYS software
基于ANSYS二次开发方矩形管辊弯仿真
7.
Comparison of the Spline-based Method of Cubic Spline Function and the Similarities and Differences of Three-moment Method
三次样条函数的基样条法和三弯矩法之异同比较
8.
Research on the Method of Calculating the Axial Force and Moment of Arbitrary Section of Lining Structures of Surge-shafts
基于ANSYS二次开发的任意截面轴力弯矩的计算方法研究
9.
The beams are designed with respect to the bending moment.
梁是按照弯矩设计的。
10.
On the influence of the bending moment waveform disturbance on the pure bending beam flexion
弯矩波形扰动对纯弯梁弯扭屈曲的影响
11.
The Calculatiou of critical load by torsion angle-bending moment matix;
用转角弯矩矩阵确定压杆的临界荷载
12.
The Influence of Cold-Formed Effect to Stress Capacity Performance of Cold-Formed Rectangular Hollow Section Beams;
冷弯效应对冷弯矩形钢管梁受力性能的影响
13.
COMPARATIVE STUDY ON BENDING STRENGTHENING METHOD OF NEGATIVE MOMENT AREA AT BEAM END IN RC FRAME
梁端负弯矩区受弯性能加固方法对比试验研究
14.
Research on the Curves Versus Moment Hysteretic Behavior of Thin-walled Cold-formed Steel Beams
冷弯薄壁型钢梁的弯矩-曲率滞回性能试验研究
15.
Calculation for Cracking Moment of SRC Flexural Member
型钢混凝土受弯构件开裂弯矩的计算初探
16.
Study of plastic limit load of the combined fittings of double elbows under in-plane bending moment
面内弯矩下双弯头组合管件的极限载荷研究
17.
Bending moments produced by lift generally have only a small effect on the resultant bending moment.
一般由升力所产生的弯矩对最终的弯矩只有很小的影响。
18.
Torque and Bending Moment in a Shaft with Combined Deformation Measured by Resistance Strain Gauge Method
电阻应变计法测量组合变形轴的扭矩和弯矩